 | | Re: Interrupt for serial data
|
|
(...) Sipke obviously realizes that more work is needed, and justs want to get to step 1 first by recognizing the interrupt. That is exactly what I would do too. I've been thinking about writing an interrupt-driven serial receive routine too, but (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: 9v lego motors
|
|
Everyone is complaining about the price of LEGO motors. There is a new product, a gear reduction motor, that is a great value. It is a super efficient DC motor with a built in gearbox that can be used for direct drive, or with one stage of gear (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sonar
|
|
If the diodes are getting hot, it does indicate a short. Fred In your message you said: (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | public apology
|
|
Yes -- I didn't think very hard and in retrospect it's fairly evident that Jan-Sipke's code is just the starting step. Sorry for being such a blunderhead. (Jan-Sipke and I have been exchanging some private messages and I think he's closing in on a (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: encoders
|
|
(...) trouble.When I try to load the file fencoder0.icb I get a message that ic cannot find the file.Any hints? (...) pulse or what dictates how the count is incremented. I think the file is named fencdr0.icb by default (not fencoder.icb). Maybe (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: encoders
|
|
-----Original Message----- From: Will Bain [SMTP:willbain@cs.umt.edu] Sent: Saturday, 14 February 1998 12:50 To: handyboard@media.mit.edu Subject: Re: encoders (...) trouble.When I try to load the file fencoder0.icb I get a message that ic cannot (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: encoders
|
|
(...) In my experience, it doesn't matter how slow the pulse is. The count is increased each time the analog port value crosses outside of the middle range defined by the two threshold values as shown below (please note that you'll need to view this (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: 68HC11 modes
|
|
The handyboard has to stay in special test mode so that it can switch into and out of 'single chip' mode at will. This is necessary to operate the LCD (which uses either a clever or gross hack depending on your taste). If you are writing code using (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | pa7 9600 serial output
|
|
Hi, I'm trying to interface the FerretTronics Servo Controller Chip FT639, to the handyboard using PA7. How can i modify the pa7_9600.asm file to transmit at 2400 baud? thanks, phet (29 years ago, 15-Feb-98, to lugnet.robotics.handyboard)
|
| |
 | | Infrared port on the HB is not working: need help!
|
|
hello! I pulled out my HB today and rtied playing around with the IR port. it does not work for some reasons. I checked the remotes: they are still transmitting! Here are the steps I took: am I missing a step? 1. loaded sony-ir.icb 2. sony_init(1); (...) (29 years ago, 15-Feb-98, to lugnet.robotics.handyboard)
|