To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3001 (-10)
  Re: looking for bridge rectifier
 
looks like they changed the part no. to 'DB101DI-ND'. Fred In your message you said: (...) (29 years ago, 21-Nov-97, to lugnet.robotics.handyboard)
 
  looking for bridge rectifier
 
HI, I'm looking for the bridge rectifier (D2) on the parts list. Digikey does not support the specified part number (DB101-ND). Can someone give me the voltage and current specs so I can find the correct part??? thanks in advance ron c (29 years ago, 21-Nov-97, to lugnet.robotics.handyboard)
 
  How to know my position??
 
Hello We are French Students and we are looking for a system to give the robot, which contains the Handy Board card, his position on a table (2*3m). Could you send us any information about this? Thank You... En français: Salut, Nous sommes des (...) (29 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
 
  How to know my position??
 
Hello We are French Students and we are looking for a system to give the robot, which contains the Handy Board card, his position on a table (2*3m). Could you send us any information about this? Thank You... En français: Salut, Nous sommes des (...) (29 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
 
  How To know my position??
 
Hello We are French Students and we are looking for a system to give the robot, which contains the Handy Board card, his position on a table (2*3m). Could you send us any information about this? Thank You... En français: Salut, Nous sommes des (...) (29 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Error in FAQ
 
In your message you said: (...) whoops. it's fixed now. thanks. one thing: the range was correctly indicated in the FAQ as $6000-$6FFF. You've got it here as $6000-$6999. Fred (29 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
 
  Error in FAQ
 
While looking through the FAq I noticed what I think is a mistake - could you check ? In the memory map it says: Expansion I/O Bank 2 $6000-$6999 Reads Enable Y3; writes enable Y5 surely this should read : reads enable Y4, writes enable Y5. Can you (...) (29 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
 
  unsubscribe
 
unsubscribe microp@geocities.com (29 years ago, 19-Nov-97, to lugnet.robotics.handyboard)
 
  OOH YES! Its Trigonometry
 
I've looked up the formula for calculating the asin and ocos. They're enlosed as .GIF attachment, because I can't type then in ASCII, but I'm sure you can view it. I hope they'll be usefull to you. Jeroen vd. Vegt. PS. I hope you already knew that (...) (29 years ago, 19-Nov-97, to lugnet.robotics.handyboard)
 
  Re: TOC4INT interrupt
 
(...) Yes, 1 mSec. (...) Time slows down (the tick counter is no longer accurate), your motors get variations in their PWM signal, and you risk losing syncronization with any servos you have out holding position. (29 years ago, 19-Nov-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR