 | | Re: IR Tower Use
|
|
If you're using Linux, see if Linux IR tools can chat with a tower -- or if some other RS-232 IR device can chat with a Lego device. I haven't had time to do such tests yet. (25 years ago, 30-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
|
| |
 | | Re: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
Another way of working around the high power and range problems would be an IR repeater. Usually these are used to extend the range of IR remote controls to another room or to a stage. (URL) two-way device might be needed here -- I've also seen some (...) (25 years ago, 30-May-01, to lugnet.robotics)
|
| |
 | | Re: Custom Firmware, IR Problems, and Dead RCXs
|
|
(...) Gee, could you tell I don't have a block diagram of the innards of the RCX? 95% of the work I've done with microcontrollers has been based on the MC68HC705J1A, J2A and K1 series (mainly because that's what I have the development tools for). (...) (25 years ago, 30-May-01, to lugnet.robotics)
|
| |
 | | Re: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
(...) Oops. I just assumed that the RMS vs Peak value of an AC transformer and the subsequent consequences for the tower were so obvious that anyone with an electronics background would have pointed it out, and since you didn't, I figured you must (...) (25 years ago, 30-May-01, to lugnet.robotics)
|
| |
 | | Re: IR Tower Use
|
|
(...) The only IrCOMM I know of is part of the IrDA standard. It provides something that looks just like a typical serial port to the application, but underneath is layered on top of IrLAP (packet based link level prototocol for IrDA). This means (...) (25 years ago, 30-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
|
| |
 | | Re: problem with floating point numbers (legOS 0.2.5)
|
|
(...) In my legOS setup (legOS0.2.5, SuSE linux 7.0), all programs work as expected. Have you changed something lately in the float-library? Or are there different versions of the gcc crsosscompiler chain? Mike (25 years ago, 29-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: IR Tower Use
|
|
(...) nod, but that made me think if we can use the IrComm package, and use a laptop's ir port to communicate with the rcx - didn't get a chance to try it yet - did anyone? Dan (25 years ago, 29-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
|
| |
 | | Re: IR Tower Use
|
|
(...) Ooops, sorry. I didn't really mean proprietary -- I meant "not normal for remote controls". (25 years ago, 29-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
|
| |
 | | gcc [was Re: problem with floating point numbers (legOS 0.2.5)]
|
|
Has anyone tried to use gcc 3.0 (one of the pres) with legOS? Just curious... Luis (...) (25 years ago, 29-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
I don't understand all the problems about blown IR-LEDs and don't believe anyone will ever see 1A flowing through his IR-LED's. My experience: I'm doing contiunuous data transfers for hours in long range mode, with fresh batteries I measure 100 mA (...) (25 years ago, 29-May-01, to lugnet.robotics)
|