To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *28739 (-10)
  RE: Custom Firmware, IR Problems, and Dead RCXs
 
(...) Ummm, that doesn't make sense. You know where the midpoint is by knowing the baud rate, and hence the bit width. The only time you need to sample at the beginning of the bit time is to look for a start bit. This is all very basic asynchronous (...) (25 years ago, 29-May-01, to lugnet.robotics)
 
  Re: download .s19 problem
 
the target of your code is probably the zero page of RAM, where the downloader bootstrap routine lives. so as your code is being downloaded, you're over-writing the hc11-ram-based dl comms code and the host side ultimately fails. fred (...) (25 years ago, 29-May-01, to lugnet.robotics.handyboard)
 
  Re: Custom Firmware, IR Problems, and Dead RCXs
 
(...) Actually, it's the computer itself that determines the duty cycle. This does mean that you could change the duty cycle, but you should be aware that it would be at the expense of noise immunity and would require a higher sampling rate from the (...) (25 years ago, 29-May-01, to lugnet.robotics)
 
  Re: Custom Firmware, IR Problems, and Dead RCXs (long)
 
(...) For what it's worth, it's not actually that bad. I don't know the specs on the NPN transistor, but I suspect 1.14A would kill it almost instantaneously. One important factor you've left out of this equation is the 9V battery itself. We often (...) (25 years ago, 29-May-01, to lugnet.robotics)
 
  Re: Custom Firmware, IR Problems, and Dead RCXs (long)
 
I'm hard pressed to understand why one would need to continually transmit from either the RCX or the tower? Data logging comes to mind, but there aren't many cases where there is a need for this. Listening can, of course, be done continously. The (...) (25 years ago, 29-May-01, to lugnet.robotics)
 
  Re: lnp rcx hostaddress [and a summer legOS release?]
 
Hi I'm preparing for the same project Vittorio's working on, a high level library in C++ to send explicit commands to rcx from a pc and back. I hope if you gonna change the low level library you will mantain a certain compatibility so that I won't (...) (25 years ago, 28-May-01, to lugnet.robotics.rcx.legos)
 
  download .s19 problem
 
Hy! I have problems downloading a self compiled file to my Handyboard (with 68HC11A1). I just wrote a little test programm: int main() { int foo = 0; while (foo < 1000) { foo++; } return(0); } and compiled it to a .s19 file with the gnu gcc 68hc11 (...) (25 years ago, 28-May-01, to lugnet.robotics.handyboard)
 
  RE: Custom Firmware, IR Problems, and Dead RCXs
 
Ralph, Thank you for painting a much clearer picture of the internal design of the IR Tower. I agree with your observations, but have a question: Is the processor in the IR Tower controllable (i.e. downloadable, like the RCX)? If it is, then there's (...) (25 years ago, 28-May-01, to lugnet.robotics)
 
  RE: Custom Firmware, IR Problems, and Dead RCXs (long)
 
(...) You are right, but the RCX and the tower are right at the hairy edge. The additional 50R impedance will leave the near mode essentially unchanged and I'll sacrifice on the high range. Start with the tower. If you use a 9V battery, the IR (...) (25 years ago, 28-May-01, to lugnet.robotics)
 
  Re: Where Can I gat the file Spirit.ocx?
 
It's on your Mindstorms CD. Just do a search and you'll find it : ) It should have already been installed on your machine as well. It'll show up in the components list under the project menu in VB as the "LEGO PBrickControl, OLE Control module." (...) (25 years ago, 28-May-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR