 | | Just Killed Another IR Tower
|
|
Hello - I received two replacement IR towers in the mail last night and have already killed one of them and am experiencing WEIRD behavior from the other. So, I'm going to try to describe what I'm doing and see if you all can provide some advice. We (...) (26 years ago, 11-May-01, to lugnet.robotics)
|
| |
 | | Re: Cool Pneumatic Page
|
|
(...) (26 years ago, 11-May-01, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: NQC vs Spirit communication speed
|
|
(...) I'm using AutoLink.Send for most things. Initially I was always closing the link at the end of each method (which mostly map to the Spirit OCX API). I've made that configurable and at present I'm running with it set to leave the link open. (...) (26 years ago, 11-May-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: NQC vs Spirit communication speed
|
|
(...) I looked into this a bit more and the poll bytecode (0x12) didn't have a case in the PredictReplyLength() switch. If you add... case 0x12: // poll return 2; then poll will be a lot faster. If you run into other bytecodes that you use a lot, (...) (26 years ago, 11-May-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: RCX Solenoid
|
|
i´ve used a solenoid on my rcx from an old copier. they are filled with them. i used it to lift and drop down a pen that i attached to my line following catepillar drive robot. i am trying to learn my rcx how to draw and sculpt... look it up(if you (...) (26 years ago, 11-May-01, to lugnet.robotics)
|
| |
 | | Re: NQC vs Spirit communication speed
|
|
The retry timing for RCX_Link uses a dynamic backoff, which is a good general purpose solution if you're going to be sending lots of packets (like a typical NQC download) and the latency through the serial driver is unknown and/or unpredictable (...) (26 years ago, 11-May-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | NQC vs Spirit communication speed
|
|
This is more a general RCX communication question, actually. As I mentioned here previously, I've ported the NQC communication code to Delphi for the purposes of modifying RcxCC to not use the Spirit OCX. At present I have a version of RcxCC that (...) (26 years ago, 11-May-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Speed Computer?
|
|
It is not seperable. The wire comes out of the little sensor and goes straight into the display part. I had wondered the same thing. But I have not taken it apart yet! I ended up making my own rotation sensors using mouse parts. You get about 4 (...) (26 years ago, 11-May-01, to lugnet.robotics)
|
| |
 | | Speed Computer?
|
|
Has anyone out there played with the Lego "Speed Computer" [5206] ? It appears to contain some kind of rotation sensor - I wonder if it could be made to work with the RCX - and perhaps avoid the missing count problems of the RCX's rotation sensor ? (...) (26 years ago, 11-May-01, to lugnet.robotics)
|
| |
 | | Re: Dead Cybermaster, please help
|
|
I tried it with a motor that worked using a battery box, but I will check that again to be sure. I just had another idea, I will use the light elemement to see if there is any power coming from the C2. I may have to pursue some kind of compensation (...) (26 years ago, 11-May-01, to lugnet.robotics.cybermaster)
|