To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *2676 (+10)
  HB problems
 
I have a problem: When I am trying to download the pcode_hb.s19 file a (...) I am using an adaptor providing 9V is that enough or should I increase or decrease the voltage When I provide the voltage on the HB pressing the STOP button the yellow (...) (29 years ago, 31-Aug-97, to lugnet.robotics.handyboard)
 
  L293 Questions
 
Hi all! Just for being sure: Is it normal that the L293Ds become warm when drawing ~0.5A for an extended period? Thanks, Jan (29 years ago, 31-Aug-97, to lugnet.robotics.handyboard)
 
  Re: HB problem
 
You need a 12V adapter and if both PWR and Batt are not OFF you are not in download mode. jm (...) should I > increase or decrease the voltage (...) (29 years ago, 31-Aug-97, to lugnet.robotics.handyboard)
 
  Re: L293 Questions
 
warm is normal, burn your fingers hot is not. jm (...) (29 years ago, 31-Aug-97, to lugnet.robotics.handyboard)
 
  (no subject)
 
It worked so thanks everybody It was the voltage it needed 12V Thanks again (29 years ago, 31-Aug-97, to lugnet.robotics.handyboard)
 
  (no subject)
 
I have a question to ask I want to use two 16V (maybe a bit more) motors and one 9V the question is To use either an Opto Darlington Isolator that my supervisor knows about, which uses the digital outputs or to cut the trace close to the J13 and (...) (29 years ago, 31-Aug-97, to lugnet.robotics.handyboard)
 
  Re: HB IR transmit circuitry problem
 
what value are you using for the R4 resistor? There was an incorrect value in some of the Handy Board documentation and it might not be fully expunged. Also, are you using a polypropylene capacitor for C6. -Fred -- This message was composed using (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
 
  HB IR transmit circuitry problem
 
As I mentioned in the previous mail message my IR transmitter on the handy board oscillates @57kHz. I ordered the exact parts# form digikey as specified in the HB documentation and also did the math. The result should be a freg between 39 -40kHz. (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
 
  Suppliers in Germany ?
 
Hello, since the available HB parts-list only names part-suppliers form the US: does anyone have a list of suppliers (and article numbers) from Germany ? I would appriciate if it could be sent to the mailinglist (or directly to me). Thank you , (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)
 
  Re: IC version 3.1 -- FYI
 
FYI IC3.1 is US$33.00 per copy (personal copy, download document), and US$20.00 with any assembled or unassembled kits. It is available in many different platforms. Patrick --00---...--- Low cost MIT Handyboard supplier and Official Distributor of (...) (29 years ago, 3-Sep-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR