 | | Trouble working with PORTC
|
|
I'm having a little trouble working with Port C on my 68hc11. A little background: the 68hc11 is part of a rug warrior pro. This board brings Port C out to an expansion socket which I can access. I'm generally using Interactive C 3.1 to work with (...) (26 years ago, 20-Jan-01, to lugnet.robotics.handyboard)
|
| |
 | | Beta Release of MacNQC
|
|
Hi all, I have been working on an updated version of MacNQC and am now ready for a public beta. If you are interested in it, it can be found at (URL). There are some new windows to control the RCX and the compile has been updated to NQC 2.2r2. Rob (...) (26 years ago, 20-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Sonar and the expansion board.
|
|
Hi, Try some of these techniques from the sites list here and see what you get. If you still get the errors in readings then you should assume that there is a problem with the board. Fortunately all chips on the board are replaceable and there is a (...) (26 years ago, 20-Jan-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: Palmpilot and RCX
|
|
(...) I've just read that version 1.2 of the program will have a programmers interface. Would this allow NQC to be ported to it and be useable for Downloading Firmware, Uploading programs and sending msg codes? With a Visor Platinum would I be (...) (26 years ago, 20-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Scout and External Iight sensor question
|
|
(...) Scout has a special command for RAW. Sensor ValueRaw(n); x = SensorValueRaw(0); This is taken from page 28 of the NQC manual. Hope that helps. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 20-Jan-01, to lugnet.robotics.scout)
|
| |
 | | Gearing down a lego motor
|
|
Hi, Before I invest a lot of time on this, what is the minimal gearing I need to do in order for a Lego motor to let itself up. How about a lego motor lifting itself and another motor up? I want the motor to be powerful but at the same time fast... (...) (26 years ago, 20-Jan-01, to lugnet.robotics.rcx, lugnet.robotics)
|
| |
 | | Re: LegOS 0.2.5 and LNP
|
|
(...) I cleaned up my code (found one bug!), the patch follows. As you may see now there are two semaphore, because two are the resources to give access to: the LNP buffer and the IR port. I modified the calling of the handlers to avoid race (...) (26 years ago, 20-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Scout and External Iight sensor question
|
|
Hi all, I read once that it is possible to use an external light sensor on on of the 2 available input ports on the SCOUT in RAW mode. I attempted to do this with SENSOR_1 in NQC with little success. Here is what I have tried. (...) (26 years ago, 20-Jan-01, to lugnet.robotics.scout)
|
| |
 | | Sonar and the expansion board.
|
|
I am having quite a problem with getting the proper readings from the sonar. Here is a little background on what I have tried. I have a total of four driver boards and four sonar modules. I have soldered on the non-polarized tantalum 0.1uF (...) (26 years ago, 20-Jan-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: adder-subtractor ????
|
|
Could you give some directive to the maximum size of it in 'bricks'? It would be a challenge to make a small adder-subtracter with a small basis, although it would probably mean that it will become a little higher than usual. Jeroen. ___...___ Visit (...) (26 years ago, 20-Jan-01, to lugnet.robotics)
|