 | | Where to Find Latest Firmware File?
|
|
Can anyone please point me to where I can download the latest firmware version? I searched the Lego Mindstorms site and can't seem to find it. Thanks! (26 years ago, 29-Dec-00, to lugnet.robotics.rcx)
|
| |
 | | Where to Find Latest Firmware File?
|
|
Can anyone please point me to where I can download the latest firmware version? I searched the Lego Mindstorms site and can't seem to find it. Thanks! (26 years ago, 29-Dec-00, to lugnet.robotics)
|
| |
 | | Re: MacNQC and RCX Troubles
|
|
(...) Bob, What type of Mac is it ? I have an original RIS 1.0. My Mac PB-G3 (wallstreet) is unable to key up the IR tower at all, but an old SE/30 works just fine. I think there are subtle differences in the voltages on Mac serial ports between (...) (26 years ago, 29-Dec-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Virtual PC 3.0 Not Finding IR Tower
|
|
I have a mac Powerbook (non-USB) running system 8.1 and using a Palm 3 serial port adapter for the IR tower. I have no fax or hotsync software loaded, nor any peripherals attached. I'm running the Lego Mindstorms software (RIS 1.0) under Virtual PC (...) (26 years ago, 29-Dec-00, to lugnet.robotics.rcx)
|
| |
 | | Virtual PC 3.0 Not Finding IR Tower
|
|
I have a mac Powerbook (non-USB) running system 8.1 and using a Palm 3 serial port adapter for the IR tower. I have no fax or hotsync software loaded, nor any peripherals attached. I'm running the Lego Mindstorms software (RIS 1.0) under Virtual PC (...) (26 years ago, 29-Dec-00, to lugnet.robotics)
|
| |
 | | Virtual PC 3.0 Not Finding IR Tower
|
|
I have a mac Powerbook (non-USB) running system 8.1 and using a Palm 3 serial port adapter for the IR tower. I have no fax or hotsync software loaded, nor any peripherals attached. I'm running the Lego Mindstorms software (RIS 1.0) under Virtual PC (...) (26 years ago, 29-Dec-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | #9244 Universal joint
|
|
Is there a substitute for the #9244 Universal joint ? ((URL) not, how can I power something that moves slighty (like a wheel with suspention, etc) ? Is the only option to use the Znap flex connector ? Thxs for any info :) Marco C. aka McViper (...) (26 years ago, 29-Dec-00, to lugnet.robotics)
|
| |
 | | Re: Motor wires
|
|
If you are careful, you can open up one of the black electrical connectors and remove the wire. The wire is attached to the connector with insulation piercing points. It is not soldered. Just lift the wire out, and cut it to the desired length. When (...) (26 years ago, 28-Dec-00, to lugnet.robotics)
|
| |
 | | MacNQC Not Recognizing Firmware File
|
|
I'm using MacNQC and when I try to download a firmware file I can't see the file in the "choose file" dialog, although I can plainly see the firmware file in the Finder. Any help would be most appreciated! (26 years ago, 29-Dec-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | MacNQC and RCX Troubles
|
|
I just got RIS1.0 and can't seem to get the RCX to respond using MacNQC or RCX Command Center running under Virtual PC 3.0. My cabling seems ok (using Palm 3 mac serial port adapter) as the green light on the IR tower comes on whenever I send a (...) (26 years ago, 29-Dec-00, to lugnet.robotics.rcx.nqc)
|