 | | USB IR tower?
|
|
Does anybody know if a USB version of the Mindstorms' IR tower has been seriously considered, and/or if one would happen to be in the works? One would normally use a USB-serial converter if stuck using only USB, but I'm also stuck in an environment (...) (26 years ago, 3-Jul-00, to lugnet.robotics)
|
| |
 | | running motors underwater
|
|
I haven't tried this myself, but I was just thinking that there could be many reasons why the motor heats up after running underwater. But first, do we know for sure that they are heating up more than they normally would? It would be interesting to (...) (26 years ago, 2-Jul-00, to lugnet.robotics)
|
| |
 | | Re: temperature sensor problem
|
|
Ben, Internally, the RCX only works with integers, but .1 degree resolution was desired for temperature sensors, so the sensor values are actually measured in .1 degree increments. A reading of 70 degrees F is stored as 700, not 70. If you change (...) (26 years ago, 3-Jul-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | VECTOR 2X
|
|
Hi all, I am currently fabricating my new HBoard based robot and have only gotten to the design stages. I have ordered a Vector 2x but haven't recieved it yet. I am not particularly well endowed with electronics or assembly language skills (very (...) (26 years ago, 3-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | temperature sensor problem
|
|
It's probably something simple and i'm about to embarrass myself, but I'm trying to write the equivalent of an RCX Code temperature sensor watcher with NQC. The motors don't seem to shut off, even when the temperature gets less than 70... (I added (...) (26 years ago, 3-Jul-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Tele-Operate Me
|
|
(...) to (...) This is likely going to require some significant web knowledge on your part. Off the top of my head, there are two ways you can do it: Simple way: Create a 'lock' file with the IP of the person visiting and the time he started (...) (26 years ago, 3-Jul-00, to lugnet.robotics.tele)
|
| |
 | | RE: running motors underwater
|
|
Yep, perfect! you would have to fill the inside of the gray piece with vaseline to prevent the water from entering the bag. Obviously, this whole method of waterproofing is only good for no more than about 3 feet deep. Anymore and the grease seals (...) (26 years ago, 3-Jul-00, to lugnet.robotics)
|
| |
 | | Re: running motors underwater
|
|
(...) Couldn't one of those grey lego cylinders for connecting 2 shafts together be used? I mean you could put one over the motor shaft to block off any water getting in there. Duncan (26 years ago, 3-Jul-00, to lugnet.robotics)
|
| |
 | | HB Batteries
|
|
I am going to use individual AA cell batteries to power the HB mounted into two 4 cell holders. My question is this, if I use NiMh cells (1300mAh) rather than NiCd cells (800 - 900 mAh) how would this effect the HB ?. My current understanding is (...) (26 years ago, 3-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | 6.8nF Capacitor
|
|
I have found that Maplins have only stopped stocking the 5% tolerance caps, they still do 10% versions. How critical is the capacitors value ?. I could probably try testing a batch of them in the shop using a multimeter but I couldn't guarentee how (...) (26 years ago, 3-Jul-00, to lugnet.robotics.handyboard)
|