To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1931 (+10)
  RE: HB books
 
Mark Robillard has written 2 good books on robotics. No one has mentioned these books here before, so I though I would list them. Here are the 2 book titles : * Microprocessor controlled robotics * Advanced microprocessor controlled robotics These (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
 
  QFP sockets
 
Hi, Thanks for the response on finding a microcontroller. I have 1 little problem left: if I'm going to use a Motorola 68F333 or the somewhat cheaper 68HC916Y1 I need a conververter from 160-lead QFP (.65 pitch) to an "normal" pinout where I can (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
 
  Re: NOTE 04/10/97 10:50:15
 
OK, I haven't looked at encoders.asm but if the following doesn't help just send more questions. (...) Sounds about right. (...) TCTL2 sets rising, falling, or both edge modes; TMSK1 arms interupts; IC event sets the TFLG1 register. (...) correct (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
 
  motor routines in lib_hb.c
 
Does anyone know why these eight speeds were chosen in lib_hb.c for the motors and what would happen if the code were re-written to allow any speed between 0 and 255? int _speed_table[]= { 0b00000000, /* speed 0 */ 0b00010001, 0b01001001, (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
 
  Re: motor routines in lib_hb.c
 
(...) These 8 bit masks are the most symmetrical way to to organize speeds of 0 through 7/7. You could rewrite the code to accept a byte and use that as the mask, but unless you think it would save space, it's a waste of time. The miniboard routines (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
 
  Re: motor routines in lib_hb.c
 
(...) Think of them as repeating binary waveforms (they are clocked out the 'enable' pin of the motor chip at 1Khz) so on an oscilloscope speed 2 (third entry) would appear.. time -> 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 (in mS) Vmotor : +--+ +--+ (...) (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
 
  Re: motor routines in lib_hb.c
 
If I'm not mistaken, (someone please corect) those speeds represent the actual shape of the waveform. Let's list some details. 1. Each bit 0 or 1 represents 0V or 9.6V. (or whatever external source) 2. Each bit represents the above voltage for a (...) (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
 
  line following
 
Hey all, I'm looking for some ideas on sensors and algorithms for a line following robot (black tape on white floor). If any of you have had some luck at this or know where I can find some info please let me know. Thanks Rajesh (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
 
  Expansion interface.
 
I have a question about the expansion interface. If it is decided upon the 1Amp 9V transistors...would it be a problem for the HB's 1Amp Voltage regulator or the fuse? (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
 
  store variables in RAM after reset
 
Hi guys, I'm new to the interactive C. Does anyone know how to declare an array of variables which can be changed by the program and stored in the RAM and their values stay the same even after reset? Second, I'm aware of something called the (...) (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR