 | | Re: IR Collision avoidance
|
|
Well, at risk of being branded a heretic, since you've brought up the issue of modulated IR, I'm going to throw out an observation I've made about the Radio Shack IR sensors which several other people on the mailing list have privately disagreed (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re[2]: IR Collision avoidance
|
|
Bill, Why is everyone using a digital device to try to detect the (analogue) distance to an object? Especially one with AGC, it makes no sense! I modulated the IR at 10KHz (high enough to be away from mains light flicker, but out of the way of the (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Re[2]: IR Collision avoidance
|
|
Richard, I've tried the op-amp method and had some success. I just don't know how I would power the -5V via the HB. Do you have any suggestions? Thanks. (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: phone cord length
|
|
Hi Jeremy, I have used a cable as long as 25 feet to connect between the handyboard and the PC. It seems to work alright for me, but the technician at school warned me that wasn't a good idea because TTL runs across the cable, and that's a bit too (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Re[2]: IR Collision avoidance
|
|
(...) Richard, In my case there are two reasons. First, I'm not trying to find the actual distance. I just want to know if there is something within a particular range. I don't care if it's an inch away or a foot. The second reason is that I can get (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR Collision avoidance
|
|
At any point are you making an effort to detect your 40kHz IR signal? If you use the sharp IR detector to receive your 40kHz signal you are going to get an initial burst when the thing first turns on and then it will average out to zero just like (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR Collision avoidance
|
|
(...) The Sharp IR modules are not being used to detect distance, they are being used simply as non-contact bumpers. This allows one to inexpensively put an arbitrarily long 'whisker' on your robot. The advantage to these things are that they are (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR Collision avoidance
|
|
Actually, I built the (...) This is exactly the same scheme I use. I'm using an IR module from Digi-key that has a side view, and five IR LED's spread around the front of the module at different angles. I have quite a few outputs, thanks to a little (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | serial comm
|
|
Good morning, I am building a handy board for the first time using the Douglas Electronics boards and parts from various sources. I have been following the assembly instructions to the letter but am now stuck at the end of section 4.4, Serial Line (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | IR xmitter/receiver idea.
|
|
Heres a IR xmitter/receiver idea for you; I've seen this approach used in equipment and it works very well, I'm not sure how well it will work for robotics but believe it can be adapted. This is difficult to explain but easy to build, so hang with (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
|