 | | Re: NQC 2.0 and some math questions
|
| A bug in the document. * and / are legal for any expressions. % is restricted to constants. I know the restrictions are confusing. The problem is that the RCX opcodes are somewhat incomplete. Now that I think about it, I can probably generate (...) (27 years ago, 23-Sep-99, to lugnet.robotics.rcx.nqc)
| | |  | | Source for IS1U60
|
| Hi! Can anybody point me to a mail order company who carries the Sharp IS1U60 infrared demodulator? Thanx...Igor (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
| | |  | | Re: Source for IS1U60
|
| (...) (URL) carries them, but they currently say they have no stock, you'd have to find what their lead-time is. Also, a Canadian firm (URL) carries them, and they DO have them in stock. HVW's cost about US$1.00 more, but at least you can get them! (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
| | |  | | Re: Source for IS1U60
|
| (...) Addendum to my last post. For my money, I would get the LiteOn unit instead. Its less fragile (nifty metal can) and has the same pinout as the Sharp GP1U58Y units, and you can get them in a variety of frequencies at (URL) Part Number 160-1153, (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
| | |  | | Re: Source for IS1U60
|
| Hi Igor - - When you need to locate parts, try this link: (URL) found a couple of sources for the IS1U60 through them. - Nick - (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
| | |  | | Re: before I reinvent the wheel
|
| No, but I have used my HP48sx to control the Fascinating Electronics board as well as an NRD535 shortwave receiver. The serial I/O of the HP48 is limited to shield, ground, tx and rx pins so in both cases I had to wire special cables to jumper (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
| | |  | | OVER 1 AMP
|
| Now, I recieved two good answers for my problems. 1) Built an H-Bridge 2) Use the LMD18200 Now has any one any documentation on an easy H bridge that I could build without wasting much time? The same goes for the LMD18200, I understand that is not (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
| | |  | | Re: OVER 1 AMP
|
| (...) www.yahoo.com, search for "H Bridge", trust me, lots of hits will comeup. Look for the 4QD pages, they talk a lot about H Bridge designs. If you aren't comfortable with electronic design, don't bother though... (...) This IS an H Bridge. Its a (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
| | |  | | Re: OVER 1 AMP
|
| Dear Paul, I have an H-bridge that I designed to run big motors. It runs at two amps continuous, and three amps intermittantly. It uses 5 volts for logic from your Handyboard, and 12 volts from a gel cell to run the motors. It also has an analog (...) (27 years ago, 23-Sep-99, to lugnet.robotics.handyboard)
| | |  | | NQC mentioned in Swedish technical weekly!
|
| Hello! When reading this week's 'Ny Teknik' (New Technic), a weekly magazine for engineers, I found a short note about NQC. The article is about Lego Mindstorms, which is just about to be released here in Sweden, and the last part of the article (...) (27 years ago, 23-Sep-99, to lugnet.robotics, lugnet.robotics.rcx.nqc)
| |