 | | Parts List
|
|
Do any of you have a more informative parts list? (Or did I miss it on the ftp site?) I am looking at buying the gear to build 25 handyboards for a High school project and need to find out if it would be cheaper to buy/ have the parts donated or (...) (27 years ago, 4-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Power Supply
|
|
(...) That is only true when you disconnect the batteries though. If you've got no batteries and were running from the power supply and disconnect, everything is lost *immediately*. There's no time at all to insert some batteries or plug it back in. (...) (27 years ago, 4-Sep-99, to lugnet.robotics)
|
| |
 | | RE: decoding a message sent by an RCX
|
|
Dave wrote... (...) Remember, you can send arbitrary ASCII data using pbFORTH. For example, to send "Hello World" you just use... : HELLO ." Hello World" CR ; Or to identify your RCX, you could use something like... : WHOAMI ." I am RCX number " (...) (27 years ago, 4-Sep-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: decoding a message sent by an RCX
|
|
Woaw ! This could be great to have a full featured rcx expansion board... It should however be not too expensive, and in my opinion very basic to allow anything to be made. A "simple" (hehe :-) 8 bit Input / Output expander would be very, very nice. (...) (27 years ago, 4-Sep-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: O'Reilly book news
|
|
(...) If there was any doubt in anyone's mind that TLG doesn't "get it", this should pretty firmly put it to bed. TLG should be falling all over themselves to give technical information to make sure the book is correct, and that it encourages people (...) (27 years ago, 4-Sep-99, to lugnet.robotics, lugnet.dear-lego)
|
| |
 | | Re: decoding a message sent by an RCX
|
|
(...) [...] I think something like this was already made by LEGO itself in the lab while creating the RCX/CyberMaster software. I say this because they seem to have forgot to remove the CABLE mode of transmission from the Spirit.ocx when deploying (...) (27 years ago, 4-Sep-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Parts List
|
|
It would be cheaper to buy it in kit form. If you try to collect the parts it may wind up more expesive due to shipping...depending on how n\many places you gotta go to...and also, availability, hunting the parts down, etc. This method is the worst. (...) (27 years ago, 4-Sep-99, to lugnet.robotics.handyboard)
|
| |
 | | RCX Currnet Rating?
|
|
Hi, I have a 9V adapter that will fit the RCX. It has a current rating of 200mA. What is the current rating for ther RCX? I have seen adapters that are rated from 100mA up to 800mA. Thx...MJ (27 years ago, 4-Sep-99, to lugnet.robotics.rcx)
|
| |
 | | Re: Power Supply
|
|
(...) It's probably a good idea to keep batteries in the RCX at all times. Robert Ashford www.apc.net/rashfor/...botics.htm (...) (27 years ago, 4-Sep-99, to lugnet.robotics)
|
| |
 | | Servo Problem! ???
|
|
Hi All The talrik bot running of a HB is doing serverly wierd things. I'vew tested these servo's on a old RC Reciver and they work fine , and my handy board can drive other servo s fine(not hacked thoe) Problem is when I give servo_a7_init(1); the (...) (27 years ago, 4-Sep-99, to lugnet.robotics.handyboard)
|