To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *11051 (+10)
  Re: Reading sensors at equal intervals.
 
(...) By standard firmware, I assume you mean using the byte codes ala NQC or something similar. If you only want semi-precise timing, you can use the wait opcode to delay for approximately 100 ms between sensor samples. If you want something more (...) (28 years ago, 25-Apr-99, to lugnet.robotics)
 
  Re: Reading sensors at equal intervals.
 
(...) I though that the four "Timer()" values read out in 100ms increments only. Is there a way to get a 1ms timer with NQC? thanks, DLC (28 years ago, 25-Apr-99, to lugnet.robotics)
 
  Rom sensor read routine
 
In writing some sensor code yesterday/today (it's 6 am), I passed over the ROM sensor code at 14c0. The documentation has been put in the usual place. The rotation code is pretty simple: the expected state machine, with split points between the four (...) (28 years ago, 25-Apr-99, to lugnet.robotics.rcx.legos)
 
  Re: Reading sensors at equal intervals.
 
(...) You are right, the timer values as seen by the firmware are in 1/10ths of a second. I lost myself in H8-land, which has a 1 ms timer that gets divided down before being seen by the firmware. -Kekoa (28 years ago, 25-Apr-99, to lugnet.robotics)
 
  Re: pneumatic switch control
 
Dennis Clark wrote in message ... (...) dropped (...) See demonstartion of the principle: (URL) pneumatic control from menu Eric Brok Visit LEGO ON MY MIND: (URL) Control section: (URL) section: (URL) (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  Re: Pics of 1999 Mindstorms items
 
S. Crawshaw wrote in message ... (...) I offered an explanation for that in a previous post. May want to look it up. Eric Brok (28 years ago, 26-Apr-99, to lugnet.robotics)
 
  RcxCC Help!
 
i downloaded the RcxCC version 2.2 and extracted it with winzip. when i try to run the RcxCC.EXE, my system say "Exception EOleSysError in module RcxCC.EXE at 00053AF9. Class not registered" does anyone know what it is and what can i do?? thanks in (...) (28 years ago, 26-Apr-99, to lugnet.robotics.rcx.nqc)
 
  Re: RcxCC Help!
 
OH! i forgot i need to install the mindstorm software before i use RcxCC!! now it works, sorry guys. (...) (28 years ago, 26-Apr-99, to lugnet.robotics.rcx.nqc)
 
  Re: RcxCC Help!
 
William: Do you have the official Mindstorms software loaded that came with the RCX? Most of the 3rd party programs need the main program loaded inorder for their program to run properly. Hope this helps... Best Regards, Patrick McLean William Ng (...) (28 years ago, 26-Apr-99, to lugnet.robotics.rcx.nqc)
 
  CMOS CAMERA
 
Anynoe did connect a CMOS camera to Handy Board ? Is possible ? (28 years ago, 26-Apr-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR