 | | Polarity Switch = Pressure Switch
|
|
Hi All, Just got my first Technic Polarity Switch and quickly put together a Pressure Switch for Pneumatics. Check out: (URL) and let me know what you think... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) It is a heck of a lot of complexity for a little added linearity. If you look at the plots on my general purpose interface section; the simple resistor interface is pretty linear. I think most of the nonlinearity in the powered version is due (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | RE: FORTH editor/IDE
|
|
(...) I'm not in the process of writing an IDE, but I'm not sure you need one either. (...) I'm going to make the pbFORTH a bit more user friendly shortly, by adding a MARKER word that essentially clears out all of your own definitions. (...) The (...) (28 years ago, 25-Mar-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | multi-device output controller
|
|
I've been considering various ways to control more than three output devices with only the three ports and came up with the following idea. I don't have the electrical design knowledge to implement, so if this idea sounds good, I'd like to (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Sharp GP2D02
|
|
I purchased two Sharp GP2D02 infrared sensors from Acroname and downloaded their interface to a Handy Board and Barry Brouilette's interface to the Handy Board. I was wondering which any of you have used and why so I can select one to use on in my (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB Memory
|
|
Stef, The HB comes with a 32K ram chip addressed at $8000 and above. A fair amount of this space is taken up with the Pcode interpreter if you run Interactive C, but there is still lots of room left for programs. Good luck, Gary Livick (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help with pointers
|
|
(...) When you do pointer arithmatic, you work in increments of what the pointer points to. So if you have a pointer to an int, as in the above example, when you add one to it, you actually make it point to the next int, not the next byte or word. (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
I have not tried pneumatics yet. I know where I will look when I try them out. This is another neat clean working device. Nice work! Bob Fay rfay@we.mediaone.net The Shop (URL) Hempel <rhempel@bmts.com> wrote in message (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Robot Mapping
|
|
Hello, I am working on an autonomous mobile robot. Which has a sonar and infared sensor incorporated into it. Right now it can avoid objects, by sensing it and backing up and turning. I want my robot to take the information from the sensors and map (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) Heck, I'd love to try some pneumatics, but you can't get a storage tank anywhere these days can you? All of the cool Technic kits are discontinued, no subs, (and while I'm whining) no shuttles, no tracked vehicles, only Throwbots and (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|