To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10341 (+10)
  names
 
Hello, some friends asked me today why I did resist the temptation of putting my name in the OS name. (It just never occurred to me.) However, there was somebody around who speaks Polish. He pointed out that Noga is Polish for leg. Totally caught me (...) (28 years ago, 25-Mar-99, to lugnet.robotics.rcx.legos)
 
  Help with pointers
 
Hi all little question: How can I ad a value to a pointer ?? int *px, x; px = &x; px = px + 1; (????? pointing to the lowbyte of x for example) Is it just NOT possible with IC or am I missunderstanding anything ???? Thanks for any help. -- Thomas (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)
 
  Re: 3-wire converter for homebrew sensors
 
(...) [snip] (...) Ahh, but the stipulated purpose for Pete's sensor brick is that it gives a _linear_ response that isn't corrupted by the non-linear diode drop caused by currents that are often less than 2ma and perhaps not past the "knee" region (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Re: names
 
(...) Will you resist the temptation 2nd time around it TLGs lawyers decide that the 'LegOS' name is a possible infringement? :) Richard(OS) (28 years ago, 25-Mar-99, to lugnet.robotics.rcx.legos)
 
  FORTH editor/IDE
 
Is anyone considering, or in the process of, writing an editor for pbFORTH on the PC? I am thinking of doing one in the style of RCX Command Center ((URL) but don't want to reinvent the wheel if there's one on the stocks. I haven't tried pbFORTH (...) (28 years ago, 25-Mar-99, to lugnet.robotics.rcx.pbforth)
 
  Polarity Switch = Pressure Switch
 
Hi All, Just got my first Technic Polarity Switch and quickly put together a Pressure Switch for Pneumatics. Check out: (URL) and let me know what you think... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: 3-wire converter for homebrew sensors
 
(...) It is a heck of a lot of complexity for a little added linearity. If you look at the plots on my general purpose interface section; the simple resistor interface is pretty linear. I think most of the nonlinearity in the powered version is due (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  RE: FORTH editor/IDE
 
(...) I'm not in the process of writing an IDE, but I'm not sure you need one either. (...) I'm going to make the pbFORTH a bit more user friendly shortly, by adding a MARKER word that essentially clears out all of your own definitions. (...) The (...) (28 years ago, 25-Mar-99, to lugnet.robotics.rcx.pbforth)
 
  multi-device output controller
 
I've been considering various ways to control more than three output devices with only the three ports and came up with the following idea. I don't have the electrical design knowledge to implement, so if this idea sounds good, I'd like to (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
 
  Sharp GP2D02
 
I purchased two Sharp GP2D02 infrared sensors from Acroname and downloaded their interface to a Handy Board and Barry Brouilette's interface to the Handy Board. I was wondering which any of you have used and why so I can select one to use on in my (...) (28 years ago, 25-Mar-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR