|
|
 | | HELP needed with non-functioning 1x2 light brick!
|
| (Not sure exactly where this should go) I have an old (say about 7-8 years old) electric light and sound brick 1 x 2 with top lamp that has never given me trouble until now. I tried clearing the muck off the contacts, rearranging it in various ways, (...) (20 years ago, 4-Feb-05, to lugnet.parts, lugnet.storage, lugnet.general)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| Oops, sorry. Here are some deep links, to use until the folder is moderated... (...) (URL) (...) (URL) Steve (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) So, like one of these? (URL) Diagonal edge (URL) Round edge Steve (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) Are you doing 3rd angle projection or 3D? 10 minutes is a lot less than it took me in Paint. I suppose once you're trained in AutoCAD, a lot of things are quick. Could you post jpegs of the results? I created bits like studs in the drawing and (...) (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) Thanks, I like to do a proper job :-) (...) Up to now, there is no plate to go with the 4x4 round brick and the half cylinders. This means that unless your round bricks have exactly 4 bricks between them, you can't support them at the side (...) (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) OK, so the piece is like this: 1. The base is 3x3. 2. Is the corner a right angle, an 8mm radius curve, or a 16mm radius curve, like this piece? (URL) 3. I assume it has 2x2 studs on top, as if two 2x3s with curved top had been superimposed at (...) (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) YIKES! (...) Well, OK, this is what I need for my students to model parts in AutoCAD! I tried this one because it looked the easiest; I'll do the others if there's interest. I don't know if anyone else has mocked these up already.. It took me (...) (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) (with random snippage) Your drawings are excellent! What detail! (...) All of your ideas (and that of the earlier, similar posts) are good. But, I'm not sure what this could be used for, although ANY 4x4 round plate would be welcomed, with or (...) (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) Very cool--I'll take those over new Bionicle parts any day. I can see the victorian porches now with that sloped brick... I wonder if you could add this to your part list, I was just thinking about this yesterday...here's what I had--I can (...) (20 years ago, 3-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) Mark, You are most definitely not alone. :) I'm guessing one of the earlier discussions you might be referring to would be this one: (URL) I must admit, I love this topic. I think as much effort, if not more, should go into which parts the (...) (20 years ago, 3-Feb-05, to lugnet.parts.custom, FTX)
|
|
