 | | Re: Base plate thickness?
|
|
(...) Scott, I'm sorry; That can't be right. More than half an inch? Did you mean 0.055 inch? I'm talking about the thickness of a baseplate, the area without the studs, the distance a block would be above my desk if the block were sitting on a (...) (17 years ago, 4-Feb-08, to lugnet.general)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) rats! (...) Thanks for the heads up, John Looks like I really have to start brushing up on my NXT 'bot building now. Dave K (17 years ago, 4-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Base plate thickness?
|
|
(...) 0.55 inch. That's measuring with a dial calipers. HTH sjf (17 years ago, 4-Feb-08, to lugnet.general)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) Dick Swan's replacement RCX firmware also does not support directly manipulating the IR led and it doesn't support microsecond timing control. Both of these features would be required in order to send the IR messages to a Power Function or R/C (...) (17 years ago, 4-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Base plate thickness?
|
|
(...) Baseplates are exactly the right thickness, such that if they are resting on studs, their studs are exactly 1 plate higher. So I guess that makes them 1 plate minus the height of a stud 8?) ROSCO (17 years ago, 4-Feb-08, to lugnet.general)
|
| |
| | Base plate thickness?
|
|
Hi all, I have this hankering to know the thickness of a baseplate. Not a regular plate, but a baseplate. I found the FAQ page with dimensions of bricks and plates and studs ( www.lugnet.com/~330/...dimensions ) but cannot seem to find out how thick (...) (17 years ago, 4-Feb-08, to lugnet.general)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
In lugnet.general, Jason J Railton wrote: <snip> (...) I'm runnign Dick Swan's alternate firmware that he sent me a while back. Dave K (17 years ago, 4-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) I doubt that's possible - a bytecode program just can't run fast enough to do the timing for the IR commands, on either brick. The NXT can only manage it because it sends them over a slow comms link to a HiTechnic IRLink sensor, then that (...) (17 years ago, 3-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) <snip> Nicely done John! Is there a tentative timeframe when NQC for the RCX will be updated to support IR to the LEGO powerfunctions? Dave K (17 years ago, 2-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics)
|
| |
| | Re: Power Functions infra-red RC protocol released!
|
|
(...) In collaboration with Jason Railton I have modified/extended the NBC and NXC API functions for the HiTechnic iRLink device in support of the newly documented Power Function modes as well as the R/C Train IR protocol. I uploaded a new (...) (17 years ago, 1-Feb-08, to lugnet.general, lugnet.technic, lugnet.trains, lugnet.robotics) !
|
