| |
0 ~Technic Gear 24 Tooth - Eighth of Center Axlehole
0 Name: s\3648s02.dat
0 Author: Lance Hopenwasser <hopenwasser@acm.org>
0 Unofficial Sub-Part
0 BFC CERTIFY CCW
0 Center Axlehole
4 16 2 5.58 9.625 0 6 9.625 0 6 0 2 5.58 0
2 24 0 6 9.625 2 5.58 9.625
1 16 2 3.79 4.8125 0 1 0 -1.79 0 0 0 0 4.8125 rect3.dat
1 16 4.761 2 8.625 2.761 0 0 0 1 0 0 0 1 rect3.dat
4 16 2 2 7.625 2 2 0 7.522 2 0 7.522 2 7.625
1 16 8.761 2 3.8125 0 0 -1.239 0 1 0 3.8125 0 0 rect1.dat
0 Top surfaces of curves around center axlehole
3 16 2 2 9.625 7.522 2 9.625 6.4993 2.3922 9.625
3 16 2 2 9.625 6.4993 2.3922 9.625 5.5361 2.9141 9.625
3 16 2 2 9.625 5.5361 2.9141 9.625 4.649 3.5571 9.625
3 16 2 2 9.625 4.649 3.5571 9.625 3.8541 4.311 9.625
3 16 2 2 9.625 3.8541 4.311 9.625 3.1636 5.1614 9.625
4 16 2 2 9.625 3.1636 5.1614 9.625 2.591 6.0954 9.625 2 5.58 9.625
3 16 2 5.58 9.625 2.591 6.0954 9.625 2.1442 7.0956 9.625
4 16 0 6 9.625 2 5.58 9.625 2.1442 7.0956 9.625 1.833 8.1459 9.625
3 16 0 6 9.625 1.833 8.1459 9.625 0 8.1459 9.625
1 16 0 8.1459 9.625 1.833 0 0 0 0 2.7867 0 -1 0 1-4disc.dat
0 Side surfaces of curves around center axlehole
0 BFC INVERTNEXT
1 16 10 10 7.625 -2.478 0 -8 -8 0 2.478 0 2 0 48\1-6cyli.dat
1 16 10 10 7.625 -2.478 0 -8 -8 0 2.478 0 1 0 48\1-6edge.dat
1 16 10 10 9.625 -2.478 0 -8 -8 0 2.478 0 1 0 48\1-6edge.dat
1 16 0 8.1459 7.625 1.833 0 0 0 0 2.7867 0 2 0 1-4cyli.dat
1 16 0 8.1459 7.625 1.833 0 0 0 0 2.7867 0 1 0 1-4edge.dat
1 16 0 8.1459 9.625 1.833 0 0 0 0 2.7867 0 1 0 1-4edge.dat
0 Connecting surfaces from pin hole to center axlehole
4 16 10 2 7.625 6.9384 2.6088 7.625 6.4993 2.3922 7.625 7.522 2 7.625
3 16 6.4993 2.3922 7.625 6.9384 2.6088 7.625 5.5361 2.9141 7.625
4 16 5.5361 2.9141 7.625 6.9384 2.6088 7.625 4.3432 4.3432 7.625 4.649
3.5571 7.625
3 16 4.649 3.5571 7.625 4.3432 4.3432 7.625 3.8541 4.311 7.625
3 16 3.8541 4.311 7.625 4.3432 4.3432 7.625 3.1636 5.1614 7.625
4 16 3.1636 5.1614 7.625 4.3432 4.3432 7.625 2.6088 6.9384 7.625 2.591 6.09
54 7.625
3 16 2.591 6.0954 7.625 2.6088 6.9384 7.625 2.1442 7.0956 7.625
3 16 2.1442 7.0956 7.625 2.6088 6.9384 7.625 1.833 8.1459 7.625
4 16 1.833 8.1459 7.625 2.6088 6.9384 7.625 2 10 7.625 1.6935 9.2124 7.625
3 16 1.6935 9.2124 7.625 2 10 7.625 1.2961 10.1164 7.625
3 16 1.2961 10.1164 7.625 2 10 7.625 0.7015 10.7205 7.625
3 16 0.7015 10.7205 7.625 2 10 7.625 2.1854 10.9326 7.625
3 16 0 10.9326 7.625 0.7015 10.7205 7.625 2.1854 10.9326 7.625
0 Rectangle at top of curve to center
1 16 1.0927 10.9326 4.6875 0 0 1.0927 0 -1 0 -2.9375 0 0 rect3.dat
0
|
|
Message is in Reply To:
 | | New part 3648a - Technic Gear 24 Tooth with 3 Axleholes [DAT]
|
| OK, after much work, refinement, and most especially help from Mark Kennedy, Chris Dee, Steve Bliss, and Orion Pobursky, I have finally finished my first part along with several supporting primitives (thus the cross-post to LCDPP). I would (...) (22 years ago, 3-Feb-03, to lugnet.cad.dev, lugnet.cad.dat.parts.primitives)
|
10 Messages in This Thread:
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
