 | | Re: Parts as volumes (instead of surfaces)
|
|
[ XFUT lugnet.cad.dev ] (...) What's "CSG descriptions"? (...) But they aren't (as you also write). Still, you are probably correct that BFC information in the LDraw parts can be used for collision detection. (...) I think it deserves further (...) (23 years ago, 7-Apr-02, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: [LCAD admin] plz re-name files...
|
|
(...) Done. But because of length limitations, I had to remove the word "Danger" from both titles. The keywords look fine to me. Steve (23 years ago, 4-Apr-02, to lugnet.cad.dev)
|
| |
| | Re: Part naming question for different versions of the same part
|
|
(...) I'd go for either option #1 or #3. In option #2, it seems like the name for 4066b.dat is misleading, because the difference between the parts is (relatively) minor. And I'd actually lean toward #3, because the difference is in the (...) (23 years ago, 4-Apr-02, to lugnet.cad.dev)
|
| |
| | Re: New Part: x192.dat - Minifig Shield Round
|
|
(...) Sure, that's possible. But by the time you get to a theoretical upper bound, you're way past the practical upper bound. So I'm not sure what the practical benefit would be. Steve (23 years ago, 4-Apr-02, to lugnet.cad.dev)
|
| |
| | Re: New Part: x192.dat - Minifig Shield Round
|
|
(...) Sorry for the mess, I'll fix my settings before I post my next part. Willy (23 years ago, 4-Apr-02, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: [LCAD admin] plz re-name files...
|
|
(...) Cool. Thanks. Also, those two files needed their Title fixed (missing the descriptor "Double", indicating fingers on both ends), and the Keywords removed. Thanks, Franklin (23 years ago, 3-Apr-02, to lugnet.cad.dev)
|
| |
| | Re: [LCAD admin] plz re-name files...
|
|
(...) OK, I've renumbered these parts. Steve (23 years ago, 3-Apr-02, to lugnet.cad.dev)
|
| |
| | Part naming question for different versions of the same part
|
|
Part 4066 is a Duplo 1x2x2 brick. I'm wondering primarily about naming conventions. This part comes in two versions. The newer version allows a Duplo top-center stud to bind in the center, and the old one doesn't (it has a supporting structure in (...) (23 years ago, 3-Apr-02, to lugnet.cad.dev)
|
| |
| | [LCAD admin] plz re-name files...
|
|
Steve, I believe that I may have used the wrong part number for a couple of my files on the Parts Tracker. I'm specifically referring to the two patterned files I made for the 1x4 click-hinge brick: 30388p01 and 30388p02. I believe these should be (...) (23 years ago, 3-Apr-02, to lugnet.cad.dev)
|
| |
| | Re: New Part: x192.dat - Minifig Shield Round
|
|
(...) Assuming some reasonable limit on the size of a number in digits (say 20 total including before and after the decimal place, that allows a very big and pretty precise number) isn't there sort of an upper bound on the line length likely to be (...) (23 years ago, 3-Apr-02, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
