 | | Re: Modelling !
|
|
(...) This is only an approximation. The LEGO bricks are not metric -- The dimensions are based on inches. The width of one brick is 5/16 inch and the height (without studs) is 6/16 inch. So 0.39370mm = 1LDU is more precise. I normally try to (...) (24 years ago, 10-Jun-00, to lugnet.cad.dev)
|
| |
| | ldglite dev version questions
|
|
Since the ldglite web page says to post questions/etc. here, here I am... Trying to compile a Linux version from the dev release on sourceforge (ldglitesrc0_6pre8.zip) has been a dismal failure - numerous undefined types, etc. Is this a (...) (24 years ago, 9-Jun-00, to lugnet.cad.dev)
|
| |
| | Re: Modelling !
|
|
(...) Some of this has come up in various discussions. I'm not sure if all of it has or not. (...) No, centering on a stud isn't necessary. Look at 3001.dat, the 2x4 brick. It is centered on X-Z, not on a stud. The same applies for all other (...) (24 years ago, 9-Jun-00, to lugnet.cad.dev)
|
| |
| | Re: Modelling !
|
|
(...) Thanks ! So, 1.00 mm = 2.5 LDU (...) I call this common sence, which I think everyone should use ! (...) Are these your opinions only, or is assumed buy other people too ? I agree with most of it ! (...) Check! (...) Check! (...) Shouldn't we (...) (24 years ago, 9-Jun-00, to lugnet.cad.dev)
|
| |
| | Re: Modelling !
|
|
(...) I believe the conversion is 0.4mm = 1 LDU. At least, that's what I always use. (...) Standards are already there. They just aren't strictly enforced. As I see it, there are two basic "orientation rules": 1. Do the same thing as other, similar (...) (24 years ago, 9-Jun-00, to lugnet.cad.dev)
|
| |
| | Re: Color and L-CAD- Some Sugessetions.
|
|
(...) The LDL 0 COLOR command already handles both of these cases. (...) I think this would be better handled as a new command, a new linetype, instead of a meta-command. (...) Hmm. That's an idea. (...) That'd be neat, too. How about a simple ... 0 (...) (24 years ago, 9-Jun-00, to lugnet.cad.dev)
|
| |
| | Getting Started (Corrections) !
|
|
Is it just me or the "Get Started" page in (URL) missing the files: lp97-13.exe lp97-14.exe which are required to be unpacked after "LDraw.exe" file and before the "Complete.exe" file. We shouldn't confuse new users ! See ya Rui Martins (24 years ago, 9-Jun-00, to lugnet.cad.dev)
|
| |
| | Modelling !
|
|
Has some of you may remember, I have modelled the super car (8880) wheels and tires, but when I modeled it I used Metric measurements (millimeters). I would Like to know if there is an approved standard for a convertion ratio, between millimeters (...) (24 years ago, 9-Jun-00, to lugnet.cad.dev)
|
| |
| | Color and L-CAD- Some Sugessetions.
|
|
(...) I feel that a new set of tags is reuired given the recent imporvemtns in L-Draw CAD systems. Might I suggest the follwoing (extremly rough spec) These commands are valid immediatly prior to a line-type. 0 SET TRANSPARENCY <Number> . For (...) (24 years ago, 9-Jun-00, to lugnet.cad.dev)
|
| |
| | Re: Write POV file... in L3Lab
|
|
Alan Gerber wrote... (...) Please mail me your (zipped) .pov file and your .dat file(s) and a little description of what you do. /Lars (24 years ago, 7-Jun-00, to lugnet.cad.dev)
|
