 | | Re: Voting Open for LCAD Parts Update 2000-01
|
|
Rui Martins <Rui.Martins@link.pt> wrote in message news:Pine.GSU.4.10.1...0@is-sv... (...) Superimposed polys are allowed, AFAIK. Maybe not the most elegant solution, but they render fine. (...) petals, (...) better (...) aprxomiation (...) I've (...) (25 years ago, 12-Apr-00, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Voting Open for LCAD Parts Update 2000-01
|
|
Another file - [3471.dat] This file has a lot of work on it, but still has some problems, specifically almost all the quads from the base are bowties. See the following image: (URL) there are a few (maybe many, but few as far as our yes can see) (...) (25 years ago, 12-Apr-00, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Voting Open for LCAD Parts Update 2000-01
|
|
(...) I have been able to test only a few parts iet, but here are my findings: - [flowers.dat] This file shows superimposed polys (tris and quads) in the petals of the flower, this is a problem in the flower itself (3742.dat), not in the flowers.dat (...) (25 years ago, 12-Apr-00, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Anyone modeling the Battle Droid?
|
|
Jonathan Wilson <wilsonj@xoommail.com> wrote in message news:38F49719.9B288B...ail.com... (...) I'll (...) Nah, it's too much of a pain. Too many intersecting cylinders. The R2 body might be a good candidate for Marc with his real CAD program. (...) (25 years ago, 12-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Anyone modeling the Battle Droid?
|
|
(...) Please finish the r2 unit first, ok. (25 years ago, 12-Apr-00, to lugnet.cad.dev)
|
| |
| | Anyone modeling the Battle Droid?
|
|
Has anyone done any work on the battle droid fig parts? If not, I think I'll make an attempt. -John Van (25 years ago, 12-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Voting Open for LCAD Parts Update 2000-01
|
|
(...) I haven't tried any of this but wouldn't Hermite curves work better ? Bezier curves don't need to go through the control points (except for the endpoints) and Hermite curves also have the advantage of letting you specify the tangent vector for (...) (25 years ago, 12-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: comments on parts up for vote- part jg1
|
|
(...) OOps. My list should have read 3 x 6 & 3 x 4 not 1 x 6 & 1 x 4. (25 years ago, 12-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: comments on parts up for vote- part jg1
|
|
(...) I don't know about those 2 parts but I have a 3x6 slope with the classic space logo here. Leonardo (25 years ago, 12-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Comments on parts up for vote- Pt 2
|
|
(...) Thanks, I'll look into this. I also noticed one flaw myself. The cross axle hole does not have a bottom; you can see the internals of the part when looking down the axle hole. Adding a 1/2 disc at the end of the cross axle hole should fix (...) (25 years ago, 12-Apr-00, to lugnet.cad.dev)
|
