 | | Re: Line in the Sand
|
|
Steve: I have a small linguistic correction, but except for that, I consider the document finished: There will be a few requirements placed on the design of rendering programs, in order to achieve correct renderings. Any program should may violate (...) (25 years ago, 6-Nov-99, to lugnet.cad.dev)
|
| |
| | Re: Line in the Sand
|
|
(...) As I said it is not ready iet. The questions (options) that where up in the air, are still there, no one as discussed them, after this spec file was created. I don't have much time now, but here are several problems. Examples: check the (...) (25 years ago, 5-Nov-99, to lugnet.cad.dev)
|
| |
| | Re: Line in the Sand
|
|
Steve: (...) I think it is ready, but I will print out a copy, and check it tonight. Play well, Jacob ---...--- -- E-mail: sparre@cats.nbi.dk -- -- Web...: <URL:(URL) -- ---...--- (25 years ago, 5-Nov-99, to lugnet.cad.dev)
|
| |
| | Re: Line in the Sand
|
|
(...) I haven't had time to reply, hope to have soon. (...) NO ! It's not quite done iet ! 8) (...) Rui Martins (25 years ago, 5-Nov-99, to lugnet.cad.dev)
|
| |
| | Re: Line in the Sand
|
|
(...) There hasn't been any discussion on this in almost two weeks. Does everyone like this spec? Any issues? Are you programmers willing to implement this? Is it ready to go to press? Steve (25 years ago, 4-Nov-99, to lugnet.cad.dev)
|
| |
| | Re: DAT to DXF
|
|
Jaco van der Molen (Sjaacko) wrote ... (...) (URL) lacks a link to 3DWin: (URL) (25 years ago, 4-Nov-99, to lugnet.cad.dev)
|
| |
| | DAT to DXF
|
|
Hi all, I know it is out there: DAT to DXF... but where? Can anyone point the URL out for me? Tnx. -- Greetingz... Sjaacko (25 years ago, 4-Nov-99, to lugnet.cad.dev)
|
| |
| | Re: My first DAT file!
|
|
(...) See my second model... posted to lugnet.cad.dat.models You may have to cut-n-paste the model out and look at it in MLCad though as LDLite gets stuck close to the end. I would really like to know what the issue is there... it makes me loath to (...) (25 years ago, 2-Nov-99, to lugnet.cad, lugnet.cad.dev)
|
| |
| | Re: My first DAT file!
|
|
John VanZwieten wrote ... (...) the (...) camera (...) I think it is unfortunate that MLCad uses the same "0 ROTATE" command as LDLite. Other parsers (like L3P :) may get confused. L3P can skip 0 ROTATE 180 0 0 REL 0 ROTATE 90 0 0 ABS 0 ROTATE 10 0 (...) (25 years ago, 1-Nov-99, to lugnet.cad, lugnet.cad.dev)
|
| |
| | Re: LDraw pieces printing
|
|
(...) Yeah, except this time I didn't back absolutely everything up, and I had to get help with the network settings. OBLEGO: What happened to the 9906 update? Hasn't it been about 4 months since we voted? (pardon my ignorance or lack of tact if the (...) (25 years ago, 30-Oct-99, to lugnet.cad.dev)
|
