 | | Re: Part number needed & New primitive submission
|
|
(...) I think the box should conform to the same geometry as the other box* primitives -- it should range from -1 to +1, not -.5 to +.5. Steve (25 years ago, 28-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: Part number needed & New primitive submission
|
|
A few things I noticed/suggestions: 1. The way you use box4nl, you are drawing a bunch of quads which will never be seen. Drop the end-quads from box4nl. 2. On the outside frame, butted-construction is not the best way to put graphics primitives (...) (25 years ago, 28-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: Part number needed & New primitive submission
|
|
Never seen the part in question, but it looks ok. The new primitive seems ok, too. Very unusual that it starts from the center and goes from -0.5 to 0.5 in all directions. I don't know if I like it, but I can surely live with it. I like the name. nl (...) (25 years ago, 25-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Part number needed & New primitive submission [DAT]
|
|
0 This part can be found in "The Red Beard Runner"??? (the second really big pirate ship that came 0 out, has a red hull). It is the arched lattice window that fits 2529 Window 1x2x3. (Note this is not 0 the rectangular latticed window pane 30044). (...) (25 years ago, 25-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Old Magnet [DAT]
|
|
I would like this magnet added to the P directory. It is used in at least two different partrs, probably some more. See (URL) for more. 0 ~Magnet Holder Old 0 Name: magnet.dat 0 To be copied into the P directory 1 8 4 0 0 0 18 0 12 0 0 0 0 12 (...) (25 years ago, 3-Jun-99, to lugnet.cad.dat.parts.primitives)
|
| |
| | Unofficial Primitive: Triangular (Prism?) [DAT]
|
|
Here are a couple primitives that I put together for a part I was doing. I have absolutely no idea how useful these would be. What I needed was a triangular piece with long sides and a face on the end. The TRI3 primitive worked, but I needed one (...) (25 years ago, 31-May-99, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Mistake in 2-4cyli?
|
|
Hi Steve, I disagree with your reasoning. (...) 2-4cyli.dat's (...) If I use 2-4cyli as the 'edge' of a part, such as a window shutter, then on one side I would have an edge line with an optional line over it, and on the other side I would just have (...) (25 years ago, 28-May-99, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Mistake in 2-4cyli? [DAT]
|
|
(...) I just looked at the file. It seems to be OK. There's one 1 conditional line for each quad, which is right. Notice that this setup gives a conditional line on one edge of the half-cylinder, but not on the other. With one side edged, and the (...) (25 years ago, 27-May-99, to lugnet.cad.dat.parts.primitives)
|
| |
| | Mistake in 2-4cyli?
|
|
For the Primitives Committee, I think I might have found a mistake in 2-4cyli. It seems there is an optional line missing (or 1 too many). I have worked out an analysis, but I can't figure out how to post it to lugnet. So if someone will send out an (...) (25 years ago, 27-May-99, to lugnet.cad.dat.parts.primitives)
|
| |
| | Un-official Primitive: 1-4ring3.dat [DAT]
|
|
0 Un-Official 4 16 0 0 3 -1.1481 0 2.7717 -1.5308 0 3.6956 0 0 4 4 16 -1.1481 0 2.7717 -2.1213 0 2.1213 -2.8284 0 2.8284 -1.5308 0 3.6956 4 16 -2.1213 0 2.1213 -2.7717 0 1.1481 -3.6956 0 1.5308 -2.8284 0 2.8284 4 16 -2.7717 0 1.1481 -3 0 0 -4 0 0 (...) (25 years ago, 20-May-99, to lugnet.cad.dat.parts.primitives)
|
