| | Re: 1-8ring3.dat, "1/8 Ring Radius 3:4"
|
|
I had a typo; the correct name is "1-8ring3.dat" (that's "one-dash-EIGHT..." and not "one-dash-FOUR..."). grumble, grumble, grumble (...) (24 years ago, 12-Jan-01, to lugnet.cad.dat.parts.primitives)
|
|
| | 1-4ring3.dat, "1/8 Ring Radius 3:4" [DAT]
|
|
I need this primitive for a new part that I'm encoding. Thanks, Franklin 0 1/8 Ring Radius 3:4 0 Name: 1-4ring3.dat 0 Author: Franklin W. Cain 0 Unofficial Primitive 0 4 16 3.000 0 0.000 2.772 0 1.148 3.696 0 1.531 4.000 0 0.000 4 16 2.772 0 1.148 (...) (24 years ago, 12-Jan-01, to lugnet.cad.dat.parts.primitives)
|
|
| | Re: Torus primitive discussion. was( Updated Primitive - 1-8t0102 1/8 torus)
|
|
(...) Because I was thinking that each section covered 90-degrees of the major circle. Otherwise, they'd be named 16t*0301.dat, since each is 1/16 of a complete torus. (I suppose they could be described as 1/8 of an inner (or outer) torus, but I (...) (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts.primitives)
|
|
| | Torus primitive discussion. was( Updated Primitive - 1-8t0102 1/8 torus)
|
|
(...) Hello, Torus comments are welcome from anyone who it may affect. I'm sure there are others out there that will use these when they become familiar with them. (...) Ok, give it a throw... :-) (...) Yes, I am afraid so. (...) I can agree to (...) (24 years ago, 8-Jan-01, to lugnet.cad.dat.parts.primitives)
|
|
| | Re: Request: Hi-res 1-4ndis.dat
|
|
Yes. Thank you, Franklin. I just discovered that I missed the 2000-02 update...! :-o /Tore (...) -- Tore Eriksson Sweden ICQ: 76066510 LEGO: MOC++++ FS,SP,TO++ TC+ LS YB@m (24 years ago, 6-Jan-01, to lugnet.cad.dat.parts.primitives)
|
|
| | Re: Request: Hi-res 1-4ndis.dat [DAT]
|
|
(...) You mean this one? Franklin 0 Disc Negative 48 0.25 0 Name: 48\1-4ndis.dat 0 Author: Franklin W. Cain (fwcain@yahoo.com) 0 Official LCAD Primitive - 2000-02 Update 0 3 16 1 0 1 1 0 0 0.9914 0 0.1305 3 16 1 0 1 0.9914 0 0.1305 0.9659 0 0.2588 3 (...) (24 years ago, 6-Jan-01, to lugnet.cad.dat.parts.primitives)
|
|
| | Request: Hi-res 1-4ndis.dat
|
|
Anyone? (24 years ago, 6-Jan-01, to lugnet.cad.dat.parts.primitives)
|
|
| | Re: Duplo parts?
|
|
In lugnet.cad.dat.parts Steve Bliss wrote... (...) Yup... :) (...) There is: Primitive substitution! I found out that we (mis)use stud4.dat by scaling its height by 5 in bricks! (and other factors in other parts) If I add a rounded edge to (...) (24 years ago, 4-Jan-01, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
|
| | Re: Updated Primitive - 1-8t0102 1/8 torus, 1-inner Radius, 2-outer radius
|
|
Paul (et al), Sorry I haven't replied to this message, I've been meaning to, but I didn't want to rush out a quick reply without thinking things through. I'm not sure I've thought things through thoroughly, but I thought I'd at least throw this out. (...) (24 years ago, 4-Jan-01, to lugnet.cad.dat.parts.primitives)
|
|
| | New Primitive: Stud4du.dat Duplo bottom tube [DAT]
|
|
I'm not terribly familiar with the naming conventions for parts, so I expect this will need a different name and/or filename... This is the bottom tube for Duplo parts. Note that it is not just a doubled System tube. The inner diameter is (...) (24 years ago, 4-Jan-01, to lugnet.cad.dat.parts.primitives)
|