To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cad.dat.partsOpen lugnet.cad.dat.parts in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / LDraw Files / Parts / 5417
5416  |  5418
Special: 
 [DAT] (requires LDraw-compatible viewer)
Subject: 
 47457 2 x 2 x 2/3 Two Top Studs, Curved Slope End
Newsgroups: 
 lugnet.cad.dat.parts
Date: 
 Fri, 10 Sep 2004 11:43:49 GMT
Viewed: 
 4188 times
  
What approach should I take to create the "Curved Slope End".  Should I create a
curved and slope line and surface primitive?

The basis for this part file (version 2) is 41855 2 x 2 x 2/3 Slope Rounded. In
the uploaded 47457v2.dat file, you'll see two pairs of quads.  The inside
surface is red, the outside is blue (I think those are the colors I put, I'm
color-blind)  I put straight lines (temporary tracers) going from the related
corners.  These lines starting from the top and ending in the bottom, need to
curve out and down.

So on the outside, a curved and sloped line should go from -10 0 -10 -20 12 30 and from 10 0 -10 20 12 -30.  Similarly in the inside -10 4 10 -16 12 -27 and from 10 4 -10 16 12 -27

Your advice please?



0 ~Curved Slope End  2 x  2 x  2/3
0 Name: 47457.dat
0 Author: Edwin H. Pilobello
0


4 6 -10 0 -10 10 0 -10 10 0 10 -10 0 10
4 16 -10 0 10 10 0 10 20 8 10 -20 8 10
4 16 -20 8 10 20 8 10 20 16 10 -20 16 10
4 6 -20 12 -30 20 12 -30 20 16 -30 -20 16 -30
4 16 -16 16 -27 16 16 -27 17 16 -30 -17 16 -30

4 16 -16 16 6 16 16 6 17 16 10 -17 16 10
4 1 -10 4 6 10 4 6 10 4 -10 -10 4 -10
4 16 -10 4 6 10 4 6 16 9 6 -16 9 6
4 16 -16 9 6 16 9 6 16 16 6 -16 16 6
4 1 -16 12 -27 16 12 -27 16 16 -27 -16 16 -27
0
0 tracers

2 1 -10 4 -10 -16 12 -27
2 1 10 4 -10 16 12 -27
2 6 -10 0 -10 -20 12 -30
2 6 10 0 -10 20 12 -30

0
4 16 -16 16 -27 -16 16 6 -17 16 10 -17 16 -30
4 16 16 16 -27 16 16 6 17 16 10 17 16 -30
4 16 -17 16 -30 -17 16 10 -20 16 10 -20 16 -30
4 16 17 16 -30 17 16 10 20 16 10 20 16 -30
4 16 -20 8 0 -20 8 10 -20 16 10 -20 16 0
4 16 20 8 0 20 8 10 20 16 10 20 16 0
4 16 -20 8 0 -20 16 0 -20 16 -10 -20 8.5 -10
4 16 20 8 0 20 16 0 20 16 -10 20 8.5 -10
4 16 -20 8.5 -10 -20 16 -10 -20 16 -20 -20 10 -20
4 16 20 8.5 -10 20 16 -10 20 16 -20 20 10 -20
4 16 -20 10 -20 -20 16 -20 -20 16 -30 -20 12 -30
4 16 20 10 -20 20 16 -20 20 16 -30 20 12 -30

3 16 -20 8.5 -10 -20 8 0 -19.239 7.391 -3.827
3 16 20 8.5 -10 20 8 0 19.239 7.391 -3.827
3 16 -20 8.5 -10 -19.239 7.391 -3.827 -17.071 5.657 -7.071
3 16 20 8.5 -10 19.239 7.391 -3.827 17.071 5.657 -7.071
3 16 -20 8.5 -10 -17.071 5.657 -7.071 -13.827 3.062 -9.239
3 16 20 8.5 -10 17.071 5.657 -7.071 13.827 3.062 -9.239
3 16 -20 8.5 -10 -13.827 3.062 -9.239 -10 0 -10
3 16 20 8.5 -10 13.827 3.062 -9.239 10 0 -10
4 16 -10 4 -6 -10 4 -10 -16 9 -10 -16 9 -6
4 16 10 4 -6 10 4 -10 16 9 -10 16 9 -6
4 16 -16 9 6 -16 9 -10 -16 16 -10 -16 16 6
4 16 16 9 6 16 9 -10 16 16 -10 16 16 6
4 16 -16 9 -10 -16 12 -27 -16 16 -27 -16 16 -10
4 16 16 9 -10 16 12 -27 16 16 -27 16 16 -10
0
1 16 -10 0 0 0 0 -10 0 1 0 10 0 0 2-4disc.dat
1 16 10 0 0 0 0 10 0 1 0 10 0 0 2-4disc.dat
1 16 -10 0 0 10 0 0 0 8 0 0 0 -10 1-4cyls2.dat
1 16 -10 0 0 10 0 0 0 8 0 0 0 10 1-4cyls2.dat
1 16 10 0 0 -10 0 0 0 8 0 0 0 -10 1-4cyls2.dat
1 16 10 0 0 -10 0 0 0 8 0 0 0 10 1-4cyls2.dat
1 16 -10 4 0 0 0 -6 0 1 0 6 0 0 2-4disc.dat
1 16 10 4 0 0 0 6 0 1 0 6 0 0 2-4disc.dat
1 16 -10 4 0 6 0 0 0 5 0 0 0 -6 1-4cyls2.dat
1 16 -10 4 0 6 0 0 0 5 0 0 0 6 1-4cyls2.dat
1 16 10 4 0 -6 0 0 0 5 0 0 0 -6 1-4cyls2.dat
1 16 10 4 0 -6 0 0 0 5 0 0 0 6 1-4cyls2.dat
1 16 0 16 -10 2 0 0 0 1 0 0 0 2 ring3.dat
1 16 0 4 -10 6 0 0 0 12 0 0 0 6 2-4cyli.dat
1 16 0 4 -10 8 0 0 0 12 0 0 0 8 2-4cyli.dat
1 16 0 5.5 -10 6 0 0 0 10.5 0 0 0 -6 2-4cyli.dat
1 16 0 6 -10 8 0 0 0 10 0 0 0 -8 2-4cyli.dat
1 16 -10 0 0 1 0 0 0 1 0 0 0 1 stud.dat
1 16 10 0 0 1 0 0 0 1 0 0 0 1 stud.dat
0
1 16 -10 0 0 -10 7.07 0 8 8 0 0 0 10 1-4ndis.dat
1 16 10 0 0 10 -7.07 0 8 8 0 0 0 10 1-4ndis.dat
1 16 -10 4 0 -6 4.242 0 5 5 0 0 0 -6 1-4ndis.dat
1 16 -10 4 0 -6 4.242 0 5 5 0 0 0 6 1-4ndis.dat
1 16 10 4 0 6 -4.242 0 5 5 0 0 0 -6 1-4ndis.dat
1 16 10 4 0 6 -4.242 0 5 5 0 0 0 6 1-4ndis.dat
1 10 0 5.5 -10 0 0 -6 0 -1.5 0 -6 0 0 1-4cyls.dat
1 10 0 5.5 -10 0 0 6 0 -1.5 0 -6 0 0 1-4cyls.dat
1 10 0 6 -10 0 0 -8 0 -2 0 -8 0 0 1-4cyls.dat
1 10 0 6 -10 0 0 8 0 -2 0 -8 0 0 1-4cyls.dat
0
2 24 -10 0 10 10 0 10
5 24 -10 0 -10 10 0 -10 0 0 0 0 1.5 -20
5 24 -10 1.5 -20 10 1.5 -20 0 0 -10 0 4 -30
0
2 24 -20 8 0 -20 8.5 -10
2 24 20 8 0 20 8.5 -10
2 24 -20 8.5 -10 -20 10 -20
2 24 20 8.5 -10 20 10 -20
2 24 -20 10 -20 -20 12 -30
2 24 20 10 -20 20 12 -30
2 24 -10 0 10 -20 8 10
2 24 10 0 10 20 8 10
2 24 -20 12 -30 -20 16 -30
2 24 20 12 -30 20 16 -30

2 24 -20 16 -30 20 16 -30
2 24 -20 12 -30 20 12 -30
2 24 -20 8 0 -20 8 10
2 24 20 8 0 20 8 10
2 24 -20 8 10 -20 16 10
2 24 20 8 10 20 16 10
2 24 -20 16 10 20 16 10
2 24 -20 16 -30 -20 16 10
2 24 20 16 -30 20 16 10
2 24 -16 16 6 -16 16 -27
2 24 16 16 6 16 16 -27
2 24 -16 16 6 16 16 6
2 24 -16 16 -27 16 16 -27
5 24 -10 0 -10 -20 8.5 -10 -20 8 0 -10 1.5 -20
5 24 10 0 -10 20 8.5 -10 20 8 0 10 1.5 -20
5 24 -10 1.5 -20 -20 8.5 -10 -10 0 -10 -20 10 -20
5 24 10 1.5 -20 20 8.5 -10 10 0 -10 20 10 -20
5 24 -10 1.5 -20 -20 10 -20 -20 8.5 -10 -10 4 -30
5 24 10 1.5 -20 20 10 -20 20 8.5 -10 10 4 -30
5 24 -10 4 -30 -20 10 -20 -10 1.5 -20 -20 12 -30
5 24 10 4 -30 20 10 -20 10 1.5 -20 20 12 -30
2 24 -10 4 6 -16 9 6
2 24 10 4 6 16 9 6
2 1 -10 4 6 10 4 6
2 24 -16 9 6 -16 9 -10
2 24 16 9 6 16 9 -10
2 24 -16 9 6 -16 16 6
2 24 16 9 6 16 16 6
0
1 16 -10 0 0 0 0 -10 0 1 0 10 0 0 2-4edge.dat
1 16 10 0 0 0 0 10 0 1 0 10 0 0 2-4edge.dat
1 16 -10 4 0 0 0 -6 0 1 0 6 0 0 2-4edge.dat
1 16 10 4 0 0 0 6 0 1 0 6 0 0 2-4edge.dat
1 16 0 16 -10 6 0 0 0 1 0 0 0 6 4-4edge.dat
1 16 0 16 -10 8 0 0 0 1 0 0 0 8 4-4edge.dat
1 16 0 4 -10 6 0 0 0 1 0 0 0 6 2-4edge.dat
1 16 0 4 -10 8 0 0 0 1 0 0 0 8 2-4edge.dat
0
1 16 -10 0 0 -10 7.07 0 8 8 0 0 0 10 1-4edge.dat
1 16 -10 0 0 -10 7.07 0 8 8 0 0 0 -10 1-4edge.dat
1 16 10 0 0 10 -7.07 0 8 8 0 0 0 10 1-4edge.dat
1 16 10 0 0 10 -7.07 0 8 8 0 0 0 -10 1-4edge.dat
1 16 -10 4 0 -6 4.242 0 5 5 0 0 0 -6 1-4edge.dat
1 16 -10 4 0 -6 4.242 0 5 5 0 0 0 6 1-4edge.dat
1 16 10 4 0 6 -4.242 0 5 5 0 0 0 -6 1-4edge.dat
1 16 10 4 0 6 -4.242 0 5 5 0 0 0 6 1-4edge.dat
1 16 0 4 -10 0 0 -6 1.5 1.5 0 -6 4.242 0 1-4edge.dat
1 16 0 4 -10 0 0 6 1.5 1.5 0 -6 4.242 0 1-4edge.dat
1 16 0 4 -10 0 0 -8 2 2 0 -8 5.656 0 1-4edge.dat
1 16 0 4 -10 0 0 8 2 2 0 -8 5.656 0 1-4edge.dat

0 COMMENT end of file



Message has 1 Reply:
  Re: 47457 2 x 2 x 2/3 Two Top Studs, Curved Slope End
 
(...) Are there many parts that will need this surface? It doesn't seem like it would be that common... If it would help you to have a subfile, then create a subpart file rather than a primitive. If I've totally missed the point of your question, (...) (20 years ago, 13-Sep-04, to lugnet.cad.dat.parts)

3 Messages in This Thread:

Entire Thread on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact
    
Custom Search

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR