Subject:
|
Re: technic engine piston square 2x2
|
Newsgroups:
|
lugnet.cad.dat.parts
|
Date:
|
Wed, 14 Jul 1999 14:54:28 GMT
|
Viewed:
|
2535 times
|
| |
|
|
In lugnet.cad.dat.parts, John VanZwieten writes:
> Bart,
>
> Try this for the curves from the sides to the top:
>
> 1 16 18 2 18 2 0 0 0 0 -2 0 -36 0 1-4cyli.dat
> 1 16 18 2.0 16 0 0 2 -2 0 0 0 2 2 1-4cyli.dat
> 1 16 18 2.0 18 0 0 2 -2 0 0 0 2 2 1-4edge.dat
> 1 16 18 2.0 -18 0 0 2 -2 0 0 0 2 -2 1-4cyli.dat
I had this, but the not rounded edges have to be added (no good primitive
available). But I can copy the optional lines from these lines and try to
adjust them to this model.
>
> Of course you'll need the same for each side, but it takes care of the
> optional lines, and will look much better in POV-Ray.
>
> And, if the sides curve smoothly to the top, no edgelines should be shown
> around the top or at the top of the sides.
thanks, I wasn't sure about these on the top
> Also, you have a number of "1 24 ... 1-4edge.dat" lines. Type 1 lines should
> never (as far as I can think) use color 24. They use color 16, since the
> color 24 of the type 2 edgelines is coded into the 1-4edge.dat. This is
> causing black edgelines on your part.
sorry, I had overseen these (even some green lines in it)
>
> Since I don't have this part, I can't really comment on it's accuracy.
thanks for the comments,
Bart
> -John Van
>
> Bart Titulaer <b.m.titulaer@phys.tue.nl> wrote in message
> news:FEv1By.2vM@lugnet.com...
> > Hi,
> >
> > I'm not sure about the name, number and description and not about the lines • in
> > combination with the rounded edges. Any comments and or suggestions?
> >
> > Bart Titulaer
> >
> >
> > 0 technic engine piston square 2x2
> > 0 Name: pistonSQR.DAT
> > 0 Author: Bart Titulaer
> > 0 Unofficial Element
>
> 1 16 18 2 18 2 0 0 0 0 -2 0 -36 0 1-4cyli.dat
> 1 16 18 2.0 16 0 0 2 -2 0 0 0 2 2 1-4cyli.dat
> 1 16 18 2.0 18 0 0 2 -2 0 0 0 2 2 1-4edge.dat
> 1 16 18 2.0 -18 0 0 2 -2 0 0 0 2 -2 1-4cyli.dat
|
|
Message has 1 Reply:
 | | Re: technic engine piston square 2x2 corrected [DAT]
|
| Thanks for the comments, I've corrected the rounded top with the primitives and corrected the false colors. Bart 0 technic engine piston square 2x2 0 Name: pistonSQR.DAT 0 Author: Bart Titulaer 0 Unofficial Element 1 16 10 0 10 1 0 0 0 1 0 0 0 1 (...) (27 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
Message is in Reply To:
| | Re: technic engine piston square 2x2 [DAT]
|
| Bart, Try this for the curves from the sides to the top: 1 16 18 2 18 2 0 0 0 0 -2 0 -36 0 1-4cyli.dat 1 16 18 2.0 16 0 0 2 -2 0 0 0 2 2 1-4cyli.dat 1 16 18 2.0 18 0 0 2 -2 0 0 0 2 2 1-4edge.dat 1 16 18 2.0 -18 0 0 2 -2 0 0 0 2 -2 1-4cyli.dat Of (...) (27 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
4 Messages in This Thread:
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
