Special:
|
[DAT] (requires LDraw-compatible viewer)
|
Subject:
|
78.DAT "Technic Ribbed Hose 120LDU Long" (MPD)
|
Newsgroups:
|
lugnet.cad.dat.parts
|
Date:
|
Sat, 10 Jun 2000 19:22:08 GMT
|
Viewed:
|
824 times
|
| |
|
|
These parts have been submitted for voting.
Fredrik
0 FILE 78.DAT
0 Technic Ribbed Hose 120LDU Long (open file for usage guide)
0 Name: 78.DAT
0 Author: Fredrik Glöckner
0 Un-Official Element
0 If you have a Ribbed Technic Hose you want to model in LDraw, you may
0 want to start by counting the number of "notches" on it. Each subpart
0 "79.DAT" and "80.DAT" is used to model one single notch, the former
0 one at the end and the latter an arbitrary one in the middle. The
0 distance between each notch should be 6.2LDU, and each subpart has the
0 notch centered in the origin. For the end segments "79.DAT", the
0 distance from the origin to the very end of the hose is 2.5LDU. This
0 way, the example hose below has a total length of 116.6LDU: Each of
0 the 17 segments have a length of 6.2LDU, while the end segments have a
0 length of 3.1LDU+2.5LDU each.
0 Note that the actual length of each hose segment is slightly longer
0 than 6.2LDU. This is chosen so that the segments overlap if used to
0 model a curved hose.
1 16 55.8 0 0 0 1 0 1 0 0 0 0 -1 79.DAT
1 16 49.6 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 43.4 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 37.2 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 31 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 24.8 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 18.6 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 12.4 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 6.2 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 0 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -6.2 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -12.4 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -18.6 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -24.8 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -31 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -37.2 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -43.4 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -49.6 0 0 0 -1 0 1 0 0 0 0 1 80.DAT
1 16 -55.8 0 0 0 -1 0 1 0 0 0 0 1 79.DAT
0
0 FILE 79.DAT
0 Technic Ribbed Hose End Segment
0 Name: 79.DAT
0 Author: Fredrik Glöckner, adapted from th.DAT by Mark R. David
0 Un-Official Element
1 16 0 2.5 0 6 0 0 0 0 0 0 0 6 4-4EDGE.DAT
1 16 0 2.5 0 6.5 0 0 0 0 0 0 0 6.5 4-4EDGE.DAT
1 16 0 1.5 0 6 0 0 0 1 0 0 0 6 4-4CYLI.DAT
1 16 0 1.5 0 6.5 0 0 0 1 0 0 0 6.5 4-4CYLI.DAT
1 16 0 1.5 0 6 0 0 0 0 0 0 0 6 4-4EDGE.DAT
1 16 0 1.5 0 6.5 0 0 0 0 0 0 0 6.5 4-4EDGE.DAT
1 16 0 1.5 0 2 0 0 0 0 0 0 0 2 RING3.DAT
1 16 0 1.5 0 8 0 0 0 0 0 0 0 8 4-4EDGE.DAT
1 16 0 1 0 1 0 0 0 0.5 0 0 0 1 4-4CON8.DAT
1 16 0 -1 0 9 0 0 0 2 0 0 0 9 4-4CYLI.DAT
1 16 0 -1 0 1 0 0 0 -0.5 0 0 0 -1 4-4CON8.DAT
1 16 0 -1.5 0 8 0 0 0 0 0 0 0 8 4-4EDGE.DAT
1 16 0 -1.5 0 2 0 0 0 0 0 0 0 2 RING3.DAT
1 16 0 -1.5 0 6.5 0 0 0 0 0 0 0 6.5 4-4EDGE.DAT
1 16 0 -1.5 0 6.5 0 0 0 -1.8 0 0 0 6.5 4-4CYLI.DAT
0
0 FILE 80.DAT
0 Technic Ribbed Hose Segment
0 Name: 80.DAT
0 Author: Fredrik Glöckner, adapted from th.DAT by Mark R. David
0 Un-Official Element
1 16 0 1.5 0 -6.5 0 0 0 1.8 0 0 0 6.5 4-4CYLI.DAT
1 16 0 1.5 0 -6.5 0 0 0 0 0 0 0 6.5 4-4EDGE.DAT
1 16 0 1.5 0 -2 0 0 0 0 0 0 0 2 RING3.DAT
1 16 0 1.5 0 -8 0 0 0 0 0 0 0 8 4-4EDGE.DAT
1 16 0 1 0 1 0 0 0 0.5 0 0 0 1 4-4CON8.DAT
1 16 0 1 0 -9 0 0 0 -2 0 0 0 9 4-4CYLI.DAT
1 16 0 -1 0 1 0 0 0 -0.5 0 0 0 -1 4-4CON8.DAT
1 16 0 -1.5 0 -8 0 0 0 0 0 0 0 8 4-4EDGE.DAT
1 16 0 -1.5 0 -2 0 0 0 0 0 0 0 2 RING3.DAT
1 16 0 -1.5 0 -6.5 0 0 0 0 0 0 0 6.5 4-4EDGE.DAT
1 16 0 -1.5 0 -6.5 0 0 0 -1.8 0 0 0 6.5 4-4CYLI.DAT
0
|
|
Message has 1 Reply:
2 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
