 | | Re: Influencing what parts people work on
|
|
(...) followed by silence from everyone else. Wrong group? Drop me a note if you think I should have posted this somewhere else... Thanks! The charter for cad.dat.parts didn't quite seem to fit. ++Lar (25 years ago, 3-Apr-00, to lugnet.cad.dev, lugnet.cad.dat.parts)
|
| |
| | Re: My first part: 2x8 tile
|
|
Whoa, waitasecondhere.... A *TWO*-by-eight tile? From which set did you get this part? I've never seen a *two*-by-eight tile... (1x8s, yeah, sure, I've got zillions of 'em, but a *2*x8?...) Thanks, Franklin (25 years ago, 3-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: My first part: 2x8 tile
|
|
That's a good start. Do you know its part number? (...) Should be: 0 Tile 2 x 8 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | My first part: 2x8 tile [DAT]
|
|
Well, it was easy to make this. Alan 0 Plate 2 x 8 1 16 60 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 40 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 20 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 0 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -20 4 0 1 0 0 0 -1 0 0 0 1 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: NEW PART: Cylinder 2 x 2 x 2/3 Inverted Dome [DAT]
|
|
Try this: 0 Cylinder 2 x 2 x 2/3 Inverted Dome 0 Name: x???.dat 0 Author: Kevin M Bane 4/02/2000 0 Un-Official Part 1 16 0 -4.5 0 6 0 0 0 0 0 0 0 6 4-4edge.dat 1 16 0 0 0 6 0 0 0 -4.5 0 0 0 6 4-4cyli.dat 1 16 0 0 0 6 0 0 0 0 0 0 0 6 4-4edge.dat 2 24 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: NEW PART: Cylinder 2 x 2 x 2/3 Inverted Dome [DAT]
|
|
Kevin B <kevinb01@netfocus.net> wrote in message news:FsEux1.Lp7@lugnet.com... (...) Well, I for one have a BIG problem with it! Looks like the ole "WordWrap" monster got me! Sorry folks! Let's try that one again! Kevin B 0 Cylinder 2 x 2 x 2/3 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | NEW PART: Cylinder 2 x 2 x 2/3 Inverted Dome [DAT]
|
|
Well, I finally decided that the Palm Tree Trunk just made my Blue Fury look a little wierd, so I churned out this part this morning. Let me know if you have any problems or comments Kevin B 0 Cylinder 2 x 2 x 2/3 Inverted Dome 0 Name: x???.dat 0 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: Brick 1 x 3 with Control Panel Pattern
|
|
(...) No. From the standard file, you need to "cut out" the surface(s) where the pattern will be. If you don't, the results will be unpredictable. /Tore (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: PART 20283.dat Slope Brick 45 4 x 6 Double Inverted [DAT]
|
|
Yes, you're absolutely correct. How sloppy of me. :-/ (...) Here's the file with your correction: 0 @Slope Brick 45 4 x 6 Double Inverted 0 Name: 20283.dat 0 Author: James Jessiman (4854.dat) 0 Author: Modified into 20283.dat by Tore Eriksson 0 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: Brick 1 x 3 with Control Panel Pattern
|
|
It's the first time i open a part with a pattern. Great work But, is it possible to re-use a standard 3622, and add only the pattern ? -- Damien et Nathalie Duquennoy 26, rue du belvédère 69210 L'ARBRESLE dduquenn@club-internet.fr (URL) Dee (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: PART 20283.dat Slope Brick 45 4 x 6 Double Inverted [DAT]
|
|
(...) There is a mistake in the latest file. (No, it's not the wrong piece this time) look at the bottom of the part in l3lab and you'll see it. I believe that the line 4 16 40 24 40 40 4 40 -40 4 60 -40 24 40 should be written as v 4 16 40 24 40 40 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New part : 2857 tyre technic 20x30 small - subpart a [DAT]
|
|
0 2857 subpart a 0 Name: S\2857a.dat 0 Author: Damien Duquennoy 0 Unofficial subpart 0 facettes 4 16 37.229 -4.504 25 37.229 4.504 25 52.12 6.306 25 52.12 -6.306 25 4 16 52.12 -6.306 25 52.12 6.306 25 58.325 7.056 23.75 58.325 -7.056 23.75 4 16 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New part : unknown tyre technic 20x30 big - subpart a [DAT]
|
|
0 tyre 20x30 technic subpart a 0 Name: S\wdd3.dat 0 Author: Damien Duquennoy 0 Unofficial subpart 0 facettes 4 16 37.42 -2.453 25 37.42 2.453 25 67.266 5.617 25 67.266 -5.617 25 4 16 67.266 -5.617 25 67.266 5.617 25 79.802 5.625 25 79.802 -5.625 25 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 4266 Technic Wheel 20x30
|
|
Yes, it's done for the two tyres i know Look at my new posts. Damien -- Damien et Nathalie Duquennoy 26, rue du belvédère 69210 L'ARBRESLE dduquenn@club-internet.fr (URL) Wilson <wilsonj@xoommail.com> a écrit dans le message : (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | New part : unknown tyre technic 20x30 big [DAT]
|
|
Hi Here is the big tyre for 4266 technic wheel. It need one subpart. PLMKWYT Damien -- Damien et Nathalie Duquennoy 26, rue du belvédère 69210 L'ARBRESLE dduquenn@club-internet.fr (URL) tyre 20x30 technic diametre 64 0 Name: wdd4.dat 0 Author: (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | New part : 2857 tyre technic 20x30 small [DAT]
|
|
Hi Here is the small tyre for 4266 technic wheel. It need one subpart. PLMKWYT Damien -- Damien et Nathalie Duquennoy 26, rue du belvédère 69210 L'ARBRESLE dduquenn@club-internet.fr (URL) 2857 technic tyre 20x30 dia 50 0 Name: 2857.dat 0 Author: (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: 4266 Technic Wheel 20x30 - Offset correction for the part. [DAT]
|
|
Hi there was a little offset mistake in my first post. Here its the good file. Damien. 0 4266 Technic Wheel 20x30 0 Name: 4266.dat 0 Author: Damien Duquennoy 0 Unofficial part 0 0 éléments base 1 16 0 0 7.5 1 0 0 0 -1 0 0 0 1 S\4266b.dat 1 16 0 0 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
| |
| | Re: A discovery? and part 3475
|
|
I haven't followed this thread, but after a brief glance, I think it is closely related to the PIPE function I (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: A discovery? and part 3475
|
|
(...) I have made a function in LDraw-mode which does this. In your example, you would put the cursor on the first type-2 line in the first edge, set the mark (C-SPC) move down to the first type-2 line in the second curve and hit C-c C-f. Voila. The (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: PART 20283.dat Slope Brick 45 4 x 6 Double Inverted [DAT]
|
|
Wrong again! This time, maybe... 0 @Slope Brick 45 4 x 6 Double Inverted 0 Name: 20283.dat 0 Author: James Jessiman (4854.dat) 0 Author: Modified into 20283.dat by Tore Eriksson 0 Un-Official Element 1 16 0 20 -20 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 0 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
