| | Re: Unofficial part: 2852 Technic Connecting Rod
|
|
(...) Thanks! I'll check it out when I get home. (...) Do you mean where the wedge thing meets the rectangular rod, on both sides? Those edges were left out intentionally, because I have really modeled a curved surface with two plane ones. There (...) (25 years ago, 19-May-99, to lugnet.cad.dat.parts)
|
|
| | Corrected part: 2854 Technic Crankshaft Centre [DAT]
|
|
0 Technic Crankshaft Centre 0 Name: 2854.dat 0 Author: Fredrik Glöckner 0 Un-Official Element 0 Thanks to John VanZwieten's great comments, I have been able to 0 correct this part. 2 24 4.34 -7 10 2.52 -5 10 2 24 4.34 7 10 2.52 5 10 2 24 -4.34 -7 (...) (25 years ago, 19-May-99, to lugnet.cad.dat.parts)
|
|
| | Re: Unofficial part: 2853 Technic Crankshaft [DAT]
|
|
Fredrik Glöckner <fredrik.glockner@bio.uio.no> wrote in message news:m3d7zydchl.fsf@....uio.no... (...) When viewed from the left side, there is no edge line along the top of the "crank case". Changing the above line to: 1 16 -10 0 -20 0 0 -9 -9 0 (...) (25 years ago, 18-May-99, to lugnet.cad.dat.parts)
|
|
| | Re: Unofficial part: 2852 Technic Connecting Rod
|
|
Fredrik Glöckner <fredrik.glockner@bio.uio.no> wrote in message news:m3g14udcwh.fsf@....uio.no... (...) The 1/4 cylinder wedge thingy connecting the lower stud with the arm doesn't join the stud quite right. It should extend further down around the (...) (25 years ago, 18-May-99, to lugnet.cad.dat.parts)
|
|
| | Unofficial part: 2853 Technic Crankshaft [DAT]
|
|
0 Technic Crankshaft 0 Name: 2853.DAT 0 Author: Fredrik Glöckner 0 Un-Official Element 0 Note that this part is probably "impossible" to make properly in LDraw 0 right now. See the discussion at 0 (URL) 1 16 -10 0 -9.8 0 0 -1 -1 0 0 0 29.8 0 (...) (25 years ago, 18-May-99, to lugnet.cad.dat.parts)
|
|
| | Unofficial part: 2852 Technic Connecting Rod [DAT]
|
|
0 Technic Connecting Rod 0 Name: 2852.dat 0 Author: Fredrik Glöckner 0 Un-Official Element 2 24 -3.04 -33.96 4 -4 -34.63 4 2 24 0 -33.25 4 -3.04 -33.96 4 2 24 0 -33.25 4 3.04 -33.96 4 2 24 3.04 -33.96 4 4 -34.63 4 2 24 4 -33.96 3.04 4 -34.63 4 2 24 (...) (25 years ago, 18-May-99, to lugnet.cad.dat.parts)
|
|
| | Re: Unofficial Part: 2x2 Plate with White Hubs
|
|
(...) That depends on having positive and accurate verification that the pieces in question require only a simple color substitution in the existing pieces, and do not have slightly different patterns. Looking at a scan of the instructions or a box (...) (25 years ago, 17-May-99, to lugnet.cad.dat.parts)
|
|
| | Re: Unofficial Part: 2x2 Plate with White Hubs
|
|
i have some minor changes to exitsing parts: brick 1 x 2 with yellow grille pattern (from blacktron I) brick 1 x 4 with white grille pattern (from futron) tile 1 x 4 with black danger stripes pattern (new part for 1999???) slope brick 45 2 x 2 with (...) (25 years ago, 17-May-99, to lugnet.cad.dat.parts)
|
|
| | Re: Unofficial Part: 2x2 Plate with White Hubs
|
|
(...) I forgot to mention in the email to you, but this piece being only a minor change to an existing part, would not require voting. It would just be added. -- Terry K -- (25 years ago, 17-May-99, to lugnet.cad.dat.parts)
|
|
| | Re: Unofficial Part: 2x2 Plate with White Hubs
|
|
(...) D'oh! Should've guessed that. Should I put his name in or leave it as-is? Also, how do I submit this for the next vote? Jeff (25 years ago, 16-May-99, to lugnet.cad.dat.parts)
|