 | | Re: Updated Part 30117
|
|
(...) Hello, I looked at the picture mentioned above, looked at the part with L3lab, LDview and l3glite~3.7.?, couldn't see the missing pieces, you are indicating. Otherwise the part looks great! Even the studs are correctly oriented. (yes, I check (...) (23 years ago, 13-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Updated Part 30117
|
|
(...) I don't have the part with me, so I'm not positive about this, but... If you look at the underside of the part you seem to be missing two triangles, one on the left and one on the right. You can see inside the bottom part of those three steps. (...) (23 years ago, 12-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | 30504 plate 8x8 sans corner [DAT]
|
|
And here is the complete piece. 0 Plate 8 x 8 without Corner 0 Name: 30504.dat 0 Author: Mark Kennedy 0 1 16 -60 4 60 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -40 4 40 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -20 4 20 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 0 4 0 1 0 0 (...) (23 years ago, 12-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | 30504s2 plate 8 by 8 sans corner: halfpart [DAT]
|
|
and now here is the half part using that new subpart thingy. 0 Plate 8 x 8 without Corner 0 Name: 30504.dat 0 Author: Mark Kennedy 0 1 16 -60 4 -60 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -60 4 -40 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -60 4 -20 1 0 0 0 -1 0 (...) (23 years ago, 12-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Updated Part 30117 [DAT]
|
|
Hi all, I have updated my 30117.dat. Paul showed me some bugs. This is the complete new part in orientation of Steves file of this part, posted some times ago. PLMKWYT / CU Bernd 0 Panel 10 x 10 x 2 1/3 Quarter Saucer Top 0 Name: 30117.DAT 0 Author: (...) (23 years ago, 11-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part : 3314.dat - Excavator Arm 2 x 6 x 2
|
|
(...) No - these were authored from scratch. Like Jason, I was amazed (or even embarressed) that they didn't exist. (...) No - I need to have the part, the time and motivation. This was just a good week - some days the visualisation comes easier (...) (23 years ago, 12-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part : 3314.dat - Excavator Arm 2 x 6 x 2
|
|
(...) Someone just requested the bucket and its arm. You are so quick. I can't believe it's true. Do you retain your unofficial parts until demand ? Are you the lamp's genie that can satisfy any part ? Or do you satisfy only 3 parts and then (...) (23 years ago, 11-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | Subpart thingy. [DAT]
|
|
Here is a new subpart I made for use on all those corner plates. Also I am working on a plate 8X8 with corner missing number 30504 available in the Harry Potter sorting hat. 0 1 16 1.50 4 -1.50 6 0 -1.50 0 4 0 6 0 1.50 box4-1.dat 1 16 -1.50 4 1.50 1 (...) (23 years ago, 11-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | New Part : 3314.dat - Excavator Arm 2 x 6 x 2 [DAT]
|
|
Here is the small excavator arm - I kept the same orientation as 828, but set the origin to match the bucket. All comments welcome. Chris 0 Excavator Arm 2 x 6 x 2 0 Name: 3314.dat 0 Author: Chris Dee (chris_w_dee@hotmail.com) 0 Unofficial part 1 16 (...) (23 years ago, 10-Oct-01, to lugnet.cad.dat.parts)
|
| |
| | New Part : x784.dat - Excavator Bucket 2 x 4 [DAT]
|
|
Here is the small excavator bucket. I have kept the same orientation as 3433.dat, but made the origin at the pivot point. Please let me know what you think. Note that temporary number x784 was previously used for the exhaust pipe part, for which the (...) (23 years ago, 8-Oct-01, to lugnet.cad.dat.parts)
|
