| | Re: ring5.dat
|
|
(...) Why? I'm aware that disc, cyli, edge, ndis have 4-4-prefix, but not the 4-4rings. And I would probably forget to look for 4-4ring primitives when there are those who begin with just ring. (...) (23 years ago, 10-Jul-01, to lugnet.cad.dat.parts.primitives)
|
|
| | Re: ring5.dat
|
|
(...) The code looks generally good. :) I haven't carefully checked the numbers, in picayune-mode. But you should: - Change the name to 4-4ring5.dat - Add a standard header. Something like: 0 Ring 5 x 1.0 0 Name: 4-4ring5.dat 0 Author: Mark Kennedy (...) (23 years ago, 9-Jul-01, to lugnet.cad.dat.parts.primitives)
|
|
| | ring5.dat [DAT]
|
|
here is a new ring primitive 0 4 16 5 0 0 4.6195 0 1.9135 5.5433 0 2.2961 6 0 0 4 16 4.6195 0 1.9135 3.5355 0 3.5355 4.2426 0 4.2426 5.5433 0 2.2961 4 16 3.5355 0 3.5355 1.9135 0 4.6195 2.2961 0 5.5433 4.2426 0 4.2426 4 16 1.9135 0 4.6195 0 0 5 0 0 (...) (23 years ago, 9-Jul-01, to lugnet.cad.dat.parts.primitives)
|
|
| | Re: New Part? - 30117 - Panel 8 x 8 x 2 2/3 [DAT]
|
|
(...) Very nice job, especially if this is your first part! Steve Bliss started this part which eventually became used as a "mock-up". I was supposed to finish it, but several other parts were needed that had a higher priority. The Link for Steve's (...) (23 years ago, 9-Jul-01, to lugnet.cad.dat.parts)
|
|
| | Re: New Part: x703.dat Wheel Hard-Plastic Fabuland (HELP NEEDED!)
|
|
Amazingly enough, this weekend's activities include fixing the LDL->DAT conversion in LDLite. Check (URL) tommorow for a version 2.2 release. -gyug (...) (23 years ago, 8-Jul-01, to lugnet.cad.dat.parts)
|
|
| | Re: New Part: x703.dat Wheel Hard-Plastic Fabuland (HELP NEEDED!)
|
|
(...) Two general solutions: 1. LDraw Add-On has an LDL2DAT converter tool, available from both the main window and from the editor. 2. LDLite has a command-line option to produce an LDraw file from an LDLite source. In the current release, this (...) (23 years ago, 8-Jul-01, to lugnet.cad.dat.parts)
|
|
| | Re: New Part: x703.dat Wheel Hard-Plastic Fabuland (HELP NEEDED!)
|
|
(...) I found it sufficient enough to open in ledit and rotate each of the boxes around the z axis by the desired angle and then you could just delete the coments. One would of caution though is that ledit turns all type 5 lines into type 4 (...) (23 years ago, 8-Jul-01, to lugnet.cad.dat.parts)
|
|
| | New Part: x704c01.dat Car Base Fabuland 14 x 4 With Wheels [DAT]
|
|
0 Car Base Fabuland 14 x 4 With Wheels 0 Name: x704c01.dat 0 Author: Tore Eriksson 0 Un-Official Shortcut 0 CMDLINE -c14 1 16 0 0 0 1 0 0 0 1 0 0 0 1 x704.dat 1 383 -60 16 110 0 120 0 4 0 0 0 0 4 4-4cyli.dat 1 383 -60 16 -110 0 120 0 4 0 0 0 0 4 (...) (23 years ago, 6-Jul-01, to lugnet.cad.dat.parts)
|
|
| | New Part: x704.dat Car Base Fabuland 14 x 4 [DAT]
|
|
0 Car Base Fabuland 14 x 4 0 Name: x704.dat 0 Author: Tore Eriksson 0 Un-Official Part 0 CMDLINE -c14 1 16 -20 4 -20 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -20 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -20 4 20 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 20 4 -20 1 0 (...) (23 years ago, 6-Jul-01, to lugnet.cad.dat.parts)
|
|
| | New Part: x703.dat Wheel Hard-Plastic Fabuland (HELP NEEDED!) [DAT]
|
|
Question: How do I make it LDraw compatible (i e "inline" the ROTATEd stuff)? 0 Wheel Hard-Plastic Fabuland 0 Name: x703.dat 0 Author: Tore Eriksson 0 Un-Official Part 0 CMDLINE -c7 1 16 0 0 -18 4 0 0 0 0 4 0 0 0 4-4edge.dat 1 16 0 0 0 4 0 0 0 0 4 0 (...) (23 years ago, 6-Jul-01, to lugnet.cad.dat.parts)
|