 | | Re: New Part: Slope Brick 55 1 x 6 x 5 [DAT]
|
|
(...) 0 Slope Brick 55 1 x 6 x 5 0 Name: 30249.dat 0 Author: Joseph H. Cardana 0 Unofficial LDraw part 0 BFC NOCERTIFY 2 24 10 120 -100 10 116 -100 2 24 6 120 -96 6 116 -96 2 24 -6 116 -96 6 116 -96 2 24 -6 120 -96 -6 116 -96 2 24 -6 4 -20 -6 116 (...) (22 years ago, 15-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: Slope Brick 55 1 x 6 x 5
|
|
You have a duplicated quad on the non sloped outside surface. Also the top part of the underside area is missing. (22 years ago, 14-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | New Part: Slope Brick 55 1 x 6 x 5 [DAT]
|
|
0 Slope Brick 55 1 x 6 x 5 0 Name: 30249.dat 0 Author: Joseph H. Cardana 0 Unofficial LDraw part 0 BFC NOCERTIFY 2 24 10 120 -100 10 116 -100 2 24 6 120 -96 6 116 -96 2 24 -6 116 -96 6 116 -96 2 24 -6 120 -96 -6 116 -96 2 24 -6 4 -20 -6 116 -96 2 24 (...) (22 years ago, 14-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: Slope Brick 55 1 x 6 x 5
|
|
(...) Do so. Please remove those incompatible ROTATION CENTER and ROTATION CONFIG lines and either add BFC NOCERTIFY or BFC-certify it. /Tore (22 years ago, 14-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: Slope Brick 55 1 x 6 x 5
|
|
Taking another closer look, I noticed only the center and zero point are wrong, but that can easily be fixed. I have done so, but would like to credit the original author on this part. "Jaco van der Molen" <jmolen@zonnet.nl> schreef in bericht (...) (22 years ago, 14-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: Slope Brick 55 1 x 6 x 5
|
|
(...) This is a very old message, but I needed this part and thought it was part of the official parts for a long time... Being indeed part 30249, why is this one still not part of the library? I can see nothing wrong with it, beside it is not BFC (...) (22 years ago, 14-Jun-04, to lugnet.cad.dat.parts)
|
| |
| | Re: Straight moving with only one rotation sensor [DAT]
|
|
I' built a similar bot, but the wheels are free-turning. Additionaly, the wheels are pressed down, so that they always have contact to the floor. It's a soccer bot for the RoboCup Junior event. 0 Untitled 0 ROTATION CENTER 0 0 0 1 "Custom" 0 (...) (22 years ago, 13-Jun-04, to lugnet.cad.dat.ideas)
|
| |
| | Re: Straight moving with only one rotation sensor
|
|
Hello y'all- Does anyone out there know where I can get discontinued lego sets (mainly the autochassis set 8860&65) at reasonable rates here in Ontario? Thanks. (22 years ago, 10-Jun-04, to lugnet.cad.dat.ideas)
|
| |
| | Straight moving with only one rotation sensor [DAT]
|
|
Hi I saw in the LEGO Mindstorms Web Page that many people made their robots with 2 motors go straight using one rotation sensor on each wheel and stopping the correct motor until both sensors were equal. I got Ultimate Accessory Set as a present (...) (22 years ago, 10-Jun-04, to lugnet.cad.dat.ideas)
|
| |
| | Re: Problem with click hinge part(s)?
|
|
(...) my click hinges, and the lugs are ALL closer to the top of vertical end wall than the bottom. The position of the lug in your new version is definitely incorrect. Whether thats a problem with the primitive or the sub-part I don't know, but it (...) (22 years ago, 10-Jun-04, to lugnet.cad.dat.parts, FTX)
|
