 | | Wedge 4 x 2 Right Slope 45 (part # 43720) [DAT]
|
|
Modeled on new pieces from the Mini MTT (set # 4491) 0 Wedge 4 x 2 Right Slope 45 0 Name: 43720.dat 0 Author: Mark Chittenden (mdublade@yahoo.com) 0 WRITE Modified from Donald Sutter's part# 41767.dat 0 MOCKUP part 0 ROTATION CENTER 0 0 0 1 "Custom" (...) (23 years ago, 20-Aug-03, to lugnet.cad.dat.parts)
|
| |
| | Star Wars Mini Models and Radiosity Renders
|
|
I've uplaoded the Star Wars Mini's to my web site: (URL) Official sets. Yes, I know there are some corrections that need to be made. I'll do them when I get home from visiting family in San Diego.. I also did another render of them all: (URL) I did (...) (23 years ago, 17-Aug-03, to lugnet.cad.ray, lugnet.cad.dat.models.sets, lugnet.starwars)
|
| |
| | Re: Stud5 and type 5 lines at edge of cylinders.
|
|
(...) I don't think the S curve problem goes away. The tangent control point works perfectly for two (same radius) curves that both curl in the same direction. It also works perfectly for a curve joining a flat edge along the tangent. However it (...) (23 years ago, 17-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Stud5 and type 5 lines at edge of cylinders.
|
|
(...) Is there a reason that the cylinder primitives haven't been updated to work like the sphere primitive? As long as there are type 5 lines on both ends of each partial cylinder, and the control point out in space is tangent to the cylinder (...) (23 years ago, 17-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | floor and back sans edge [DAT]
|
|
for placing models on. 0 floor and back sans edge 0 Name: rondback.ldr 0 Author: jeroendehaan@mac.com 0 ROTATION CENTER 0 0 0 1 "Custom" 0 ROTATION CONFIG 0 1 1 16 -110 -396 1250 0 0 -500 500 0 0 0 -2500 0 1-4cyli.dat 1 16 110 604 1250 0 0 500 -500 (...) (23 years ago, 16-Aug-03, to lugnet.cad.dat.scenes)
|
| |
| | Re: Stud5 and type 5 lines at edge of cylinders.
|
|
(...) So the problem could be solved by using high res primitives? I'll have to try that out. (23 years ago, 16-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Stud5 and type 5 lines at edge of cylinders.
|
|
(...) Ahh, the dreaded S-curve cylinder join rears it's ugly head again. I voted to ignore this a while back and gave my reasons. (URL) disagreed at the time. Don (23 years ago, 15-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Stud5 and type 5 lines at edge of cylinders. [DAT]
|
|
I recently reworked the stud 5 primitive to make use of more quarter cylinders. I then noticed that when viewed there were edge lines apearing where they shouldn't. If you look at the primitive from various points you can see this occur. 0 Stud (...) (23 years ago, 15-Aug-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: PT Update Times (Was: 44567)
|
|
(...) Not really. I know what needs to change, I just haven't gotten around to making it happen. Steve (23 years ago, 12-Aug-03, to lugnet.cad.dat.parts)
|
| |
| | Re: Train Track 9V Half Straight
|
|
(...) I'll never ask again for the using of parts ;-) CU Bernd (23 years ago, 10-Aug-03, to lugnet.cad.dat.parts)
|
