|
|
 | | Re: Lpub find edges
|
| (...) Cylinders would not resolve every edge lines, at curved surfaces that would be a problem. There are comercial renderes that do that line and flat surface stuff. They are used a lot to blend 3D CG with cell animation drawings. I have not (...) (21 years ago, 3-Apr-04, to lugnet.cad, lugnet.cad.dev, FTX)
| | | | | Re: Lpub find edges
|
| (...) Ok! Now I got it right: (URL) everyone. Paulo (21 years ago, 3-Apr-04, to lugnet.cad)
| | | | | Re: Lpub find edges
|
| (...) This is so very true, and troublesome. POV-Ray does not support the concept of a line in 3D space, so L3P cannot directly translate LDraw lines to POV-Ray entities. Lars, at one point we talked about the possibility of having L3P use cylinders (...) (21 years ago, 3-Apr-04, to lugnet.cad, lugnet.cad.dev, FTX)
| | | | | Pull back motor LDRAW parts available?
|
| Hello, are there any unofficial LDRAW parts of the new pull back motors (especially type 7, part-nr.32283c03 ) available? This is the motor: (URL) I'm also searching for a dat file of the Wheel 36.8x14 (part-nr: 44293): (URL) If anyone knew where I (...) (21 years ago, 3-Apr-04, to lugnet.cad.dat.parts, FTX)
| | | | | Library version 501 is now available!
|
| A new version of the Library is available now, version 501! 8 new pieces have been added, a few modified and all of the textures have been tweaked a little bit, so that they look even more realistical than they did before. Half the Gallery has been (...) (21 years ago, 3-Apr-04, to lugnet.cad)
| | | | | Re: Part x224: Windscreen 8 x 6 x 2 Curved
|
| (...) There should be no conflict.[1] When this part becomes an official LDraw part it will (probably) have number 462, and Peeron and (hopefully) BrickLink will update to use that number. (21 years ago, 3-Apr-04, to lugnet.cad.dat.parts)
| | | | | Re: Lpub find edges
|
| (...) Ok now I understand, these numbers are trick... (...) It is set that way. Thanks (URL) (21 years ago, 3-Apr-04, to lugnet.cad, FTX)
| | | | | Re: Snatch it?
|
| (...) (snip)... (...) I'd be more comfortable if we knew who Gonta was... BUT (...) your point is well taken. If someone did that and gave credit and a bit of history in the remarks it would be hard to see how anyone could say rights weren't being (...) (21 years ago, 3-Apr-04, to lugnet.cad.dat.parts)
| | | | | Re: Lpub find edges
|
| (...) You should note that the value for the line width is relative to the resolution of the image, not relative to the size of the object being rendered. So, if you render a brick that takes up almost all of the space in your image, your line will (...) (21 years ago, 3-Apr-04, to lugnet.cad, FTX)
| | | | | Re: Lpub find edges
|
| (...) Paulo, the "right parameters" depends on what size resolution you are creating your BIs. I use a 1600x1200 image resolution for me BIs and then shrink them to whatever I need. Based on a 1600x1200 res, I have found that these parameters work (...) (21 years ago, 3-Apr-04, to lugnet.cad, FTX)
|
|
