 | | Re: More cylinder primitives wanted
|
|
(...) Sounds good, I could have used this part several times. Another series "primitive" part I use is x-xhole.dat and x-xhola.dat. They get inlined before the part gets released. The x-xhole.dat is made up of an edge, ndis, cyli, edge, and a ndis. (...) (21 years ago, 10-Dec-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | More cylinder primitives wanted
|
|
Just like there are a huge number of different box primitives, with different number of edges and surfaces, I wish there were some more cylinder primitives from n-ncyli.dat We have: * cyli = cylinder with walls, no edges, no disc On my wish list: * (...) (21 years ago, 9-Dec-03, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: anyone modeling these?
|
|
(...) I started out on one pull-back motor but lost it somewhere. I guess your motor is larger? (URL) (21 years ago, 9-Dec-03, to lugnet.cad.dat.parts, FTX)
|
| |
| | Train wheels and train motors (4.5 and 12 Volt)
|
|
When I searched the Partstracker to see if the first train motor (4 x 12 x 4) has been done, I only found the newer motor (4 x 12 x 3 2/3), x215. Shouldn't this part have it's size in the part name to distinguish it from the older and a bit larger (...) (21 years ago, 9-Dec-03, to lugnet.cad)
|
| |
| | anyone modeling these?
|
|
Hi, I'm thinking of modeling a couple of parts, but before I do I'd like to check that no-one is already doing them. I've checked the parts tracker and they don't appear there. The parts are: (URL) 'Brick 1 x 4 with Sloped Ends and Two Top Studs' (...) (21 years ago, 9-Dec-03, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: New Part mock-up: Minifig Forestman Cap
|
|
(...) Awesome! Thanks Chris! I've been wanting this one for a long time. Great work! ~Mike (21 years ago, 9-Dec-03, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part mock-up: Minifig Forestman Cap
|
|
(...) ... and after three years as work in progress, I have finally figured out the feather hole. The complete part is posted to the Parts Tracker at (URL) (21 years ago, 8-Dec-03, to lugnet.cad.dat.parts)
|
| |
| | Wheel 11 x 8 with Center Groove/Tyre 17.5 x 6 with Shallow Staggered Treads?
|
|
Is anyone working on these? Wheel 11 x 8 with Center Groove Tyre 17.5 x 6 with Shallow Staggered Treads (2 URLs) x265.jpg x266.jpg Note that x265.dat and x266.dat at LDraw.org are completely different parts: Lightbrick 2 x 2 Type I 4.5V Lightbrick 2 (...) (21 years ago, 8-Dec-03, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: MOTM / SOTM Voting For December Is Now Open
|
|
(...) Thanks. It works now. A (21 years ago, 8-Dec-03, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: MOTM / SOTM Voting For December Is Now Open
|
|
(...) You have to give the system some time for your newly registered account to be filtered throughout all the site's modules. Log out, wait 30 minutes, log in, and try again. You should now be able to vote. -Orion (21 years ago, 7-Dec-03, to lugnet.cad.dev.org.ldraw)
|
