To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cadOpen lugnet.cad in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / *23770 (-10)
  New Part: 3001p59.dat - Brick 2 x 4 with Shell text  [DAT]
 
Just arrived to me from Denmark today. :o) /Tore 0 Brick 2 x 4 with Shell text 0 Name: 3001p59.dat 0 Author: Tore Eriksson 0 Unofficial Element 0 CMDLINE -c15 1 16 20 4 0 1 0 0 0 -5 0 0 0 1 stud4.dat 1 16 0 4 0 1 0 0 0 -5 0 0 0 1 stud4.dat 1 16 -20 (...) (23 years ago, 10-Apr-02, to lugnet.cad.dat.parts)
 
  Re: matching pattern numbers???
 
(...) That seems perfectly reasonable. (...) Cool! Thanks! :-) (...) [snip] (...) Very nicely done, sir! ;-) I've got some of the new (2002) 'figs, so would you mind if I give you more info for this list, or else use your info in a list of my own? (...) (23 years ago, 10-Apr-02, to lugnet.cad.dev)
 
  Re: Parts as volumes (instead of surfaces)
 
(...) Well, I can have a twisted mind sometimes. I know these moments when the best idea today, will just be plain stupid tomorrow. Thanks to Eric Olson for more precision: he used bounding boxes, not collisions. Also I still think, whereas higher (...) (23 years ago, 10-Apr-02, to lugnet.cad.dev.org.ldraw)
 
  Han Solo "gunbelt" hips/legs (was "matching pattern numbers???")
 
(...) As promised: Minifig Hips & Legs with SW Gunbelt Pattern (Complete) (URL) Hips with SW Gunbelt Pattern (URL) Leg Right with SW Gunbelt Pattern (URL) (23 years ago, 10-Apr-02, to lugnet.cad.dev, lugnet.cad.dat.parts)
 
  Re: Modeling String
 
(...) Incidentally, I have considered it. But so far I have concluded that the mathematics are too complicated for an analytical solution. And I am a bit tired of programming numerical optimalization.. Fredrik (23 years ago, 10-Apr-02, to lugnet.cad)
 
  part(s) posted... (set #4817)
 
I went with pattern number "4f", since "4b" has been taken by some other torso. Minifig Hips & Legs with Leather Armor Pattern (Complete) (URL) Hips with Leather Belt (Red Studs) Pattern (URL) Leg Right with Leather Straps (Red Studs) Pattern (URL) (...) (23 years ago, 10-Apr-02, to lugnet.cad.dev)
 
  Re: Beta testers needed
 
I've created a temporary webpage for LD4DModeler, in time you can download the beta there. The url is: (URL) (23 years ago, 10-Apr-02, to lugnet.cad)
 
  Re: Parts as volumes (instead of surfaces)
 
(...) That was only bounding boxes (minus the studs). The piece in question was matched against all other pieces, any pieces in a line above or below were put into a list. In case one of them intersected the piece in question, a new place would be (...) (23 years ago, 10-Apr-02, to lugnet.cad.dev.org.ldraw)
 
  Enhancement request - File dialogs
 
I think the File dialogs could benefit from some improvement in how path is determined. This applies to at least export model and export submodels (in Multipart mode) Both default to the root of the C drive and don't remember last filepath selected. (...) (23 years ago, 10-Apr-02, to lugnet.cad.mlcad)
 
  Re: Parts as volumes (instead of surfaces)
 
(...) So stud4 would be decomposed into 16 trapezoidal prisms? That sounds like a fair amount of mark up. (...) Nod, true. But I'd rather decompose a 1x1 brick into 6 volumes (4 walls, 1 top and the stud) than 46 (one volume for each surface (...) (23 years ago, 10-Apr-02, to lugnet.cad.dev.org.ldraw)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR