 | | Re: New Part, 99% done: 6203.dat - Container ???
|
|
(...) I'm not sure where to go with this one. Generally, parts like this go into Minifig Accessory. But this part isn't exactly minifig scale. Hmm. (...) I don't think so. Typical primitive files only have an optional line at one end. Check out this (...) (23 years ago, 13-Mar-02, to lugnet.cad.dat.parts, lugnet.cad)
|
| |
| | Re: General question on ldr and mpd files ...
|
|
(...) Yes, that's correct. Well, I haven't checked lately, hold on.... er, never mind. I'm wrong. My bad. LDraw and LEdit *will* add a '.dat' extension to a filename you specify on the command line, so the command: ldraw tt will cause ldraw to (...) (23 years ago, 13-Mar-02, to lugnet.cad)
|
| |
| | Re: New Part, 99% done: 6203.dat - Container ???
|
|
(...) I agree. I think the problem is that the current half cylinder primitives expect to be mated with other cylinder primitives to create a whole cylinder. Connect edge A with optional line to edge B without optional line. But connect edge A to (...) (23 years ago, 13-Mar-02, to lugnet.cad.dat.parts, lugnet.cad)
|
| |
| | Some question about Quicktime Pro and about Lugnet
|
|
Hi to all. I have great news for MAC users I got QuickTime Pro 5 finally so I'm planning to start making animation in MOV also but only 15 frames per second since mpeg has to be 24 at least and as I don't like MS AVI I'll be using MOV files as an (...) (23 years ago, 13-Mar-02, to lugnet.cad)
|
| |
| | Re: Part Question - Brusch Axle and Holder [DAT]
|
|
And at last the axle. Should I make the cuts, or not? 0 Car Wash Brush Axle 0 Name: 2474.dat 0 Author: Bernd Broich 0 Unofficial Part 0 Left End 1 16 -72 0 0 0 1 0 1.5 0 0 0 0 1.5 4-4edge.dat 1 16 -72 0 0 0 1 0 4.5 0 0 0 0 4.5 4-4edge.dat 1 16 -72 0 (...) (23 years ago, 13-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Part Question - Brusch Axle and Holder [DAT]
|
|
0 ~Brush Car Wash Subpart 0 Name: s\2473s01.dat 0 Author: Bernd Broich 0 Unofficial Subpart 1 16 2.606 0 9.766 0.1996 1.3094 0 0 0 -0.2 -0.0131 19.9771 0 4-4con1.dat 1 16 3.916 0 29.744 0.1996 0.0654 0 0 0 -0.2 -0.0131 0.9979 0 4-4edge.dat 1 16 (...) (23 years ago, 13-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Part Question - Brusch Axle and Holder [DAT]
|
|
Here is the corrected bush with cylinders instead of lines and 46 LDU instead of 44. 0 Car Wash Brush 0 Name: 2473.dat 0 Author: Bernd Broich 0 Unofficial Update 1 16 0 0 0 -10 0 0 0 1 0 0 0 -10 48\1-4edge.dat 1 16 0 0 0 -10 0 0 0 1 0 0 0 10 (...) (23 years ago, 13-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Part Question - Brusch Axle and Holder [DAT]
|
|
Here is the holder. I hope the orientation is correct. 0 Car Wash Brush Holder 0 Name: 2475.dat 0 Author: Bernd Broich 0 Unofficial Part 0 Left End 1 16 63.5 0 0 0 -1 0 0 0 -0.5 -0.5 0 0 1-4rin12.dat 1 16 63.5 0 0 0 -1 0 0 0 -0.5 0.5 0 0 (...) (23 years ago, 13-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part, 99% done: 6203.dat - Container ???
|
|
(...) www.peeron.com calls it Case Oval. I don't know, it seems like it's not only used in Belville sets. ( (URL) ) (...) <snip> I have noticed that kind of problems too. It must be due to the current primitives, and not flaws in my parts authoring. (...) (23 years ago, 13-Mar-02, to lugnet.cad.dat.parts, lugnet.cad)
|
| |
| | Re: Parts tracker ampty?
|
|
(...) You're right, for me both the Parts Tracker Active Parts List as the Certification Status List are empty too. Greetings, M. Moolhuysen. (23 years ago, 13-Mar-02, to lugnet.cad)
|
