 | | Re: MOTM voting for February
|
|
"Brad Hamilton" <bhamilto1@home.com> wrote in message news:G7pAup.B5u@lugnet.com... (...) Same here! I just have to quit gawking and think 'what will look the best on the front page?' because that's the point of the contest :) -Tim (24 years ago, 25-Jan-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: MOTM voting for February
|
|
There is an excellent selection this month! It took me about 10 minutes to decide on my vote. Tim Courtney <tim@zacktron.com> wrote in message news:G7orCs.7oH@lugnet.com... (...) news:G7oMqH.GtD@lugnet.com... (...) I've (...) for my (...) (24 years ago, 25-Jan-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Torus primitive discussion. was( Updated Primitive - 1-8t0102 1/8 torus) [DAT]
|
|
Sorry about taking so long to reply to this message. I have been working on trying to make a few of these torii mentioned below. (...) That is what I meant. :-) (...) If we worked with the method used for the rings and similar existing primitives, I (...) (24 years ago, 25-Jan-01, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: New Part In Progress: Brick 1x4 with Studs Hollow on side
|
|
Xcalabur <Xcalabur@rocketmail.com> wrote in message > (...) grey). (...) It was also in the UCS X-Wing Gary (24 years ago, 25-Jan-01, to lugnet.cad)
|
| |
| | Re: New Part In Progress: Brick 1x4 with Studs Hollow on side
|
|
(...) That was an error on my behalf... I forgot to mention that the set is still on its way to my house, so i am working from a picture in a magazine that shows the set at just the right angle that the part is visible. Sence i could only see 1 side (...) (24 years ago, 25-Jan-01, to lugnet.cad)
|
| |
| | Re: Floating optional lines on 977 Minifig hand
|
|
(...) This just demonstrates how useful L3Lab is as a checker, and how difficult it was to check parts before. I think the ability for it to show all type 5 lines was something Lars put in at my request - thanks, the effort has been shown to be (...) (24 years ago, 25-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: MOTM voting for February
|
|
"Terry K" <legoverse@yahoo.com> wrote in message news:G7oMqH.GtD@lugnet.com... (...) DUUDE...this is going to be tough! These are some of the best renderings I've seen up period (and I'm not referring to my entry). I doubt I could vote for my own (...) (24 years ago, 24-Jan-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | MOTM voting for February
|
|
Salutations virtual brickheads, Voting for the ldraw.org MOTM is now up and running; (URL) intriguing variety this time 'round. -- Terry K -- (24 years ago, 24-Jan-01, to lugnet.announce, lugnet.cad, lugnet.cad.dev.org.ldraw)
|
| |
| | Floating optional lines on 977 Minifig hand
|
|
Last night was toying with some minifig dat files I created with the nifty leocad minifig modeler when I spotted what looked like some bad type 5 lines on the hands. So I loaded just part 977 into l3lab and zoomed in. Sure enough, when you spin the (...) (24 years ago, 24-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: DAT to GIF/JPG/EPS
|
|
(...) Did you use this double size method to generate the recently posted horse and cow instructions? They look nice. I might have to reorder my priorities. I've been working on replacing the pathetic ldglite gui with something a bit more user (...) (24 years ago, 24-Jan-01, to lugnet.cad)
|
