 | | Re: parts available?
|
|
all of the parts are available for the 8448 except for the wheels, I dont know about the other 2 sets, I think that all of the parts for the 8445 are available but I think there are some missing for the 8444. What parts in particular do you want? (24 years ago, 14-Sep-00, to lugnet.cad.mlcad, lugnet.cad, lugnet.cad.dev.org.ldraw)
|
| |
| | Posting notices about ldraw.org (and other website) inaccessability
|
|
It seems to me that every so often someone posts about not being able to get to www.ldraw.org. I'm concerned with some problems that users of the site may have getting to it - its definitely frustrating every time a site goes down. One thing I'd (...) (24 years ago, 14-Sep-00, to lugnet.admin.general, lugnet.cad.dev.org.ldraw, lugnet.general)
|
| |
| | parts available?
|
|
hello i was thinking about doing my technic set up in mlcad...but i dont want to put that kind of effort into it if all the parts arent available so, my question is this do you know if all the parts are available for ldraw and mlcad for the (...) (24 years ago, 14-Sep-00, to lugnet.cad.mlcad, lugnet.cad, lugnet.cad.dev.org.ldraw)
|
| |
| | part number for "Animal Cattlehorn" and "Minifig Accessory Islander Crest"
|
|
According to this post "(URL) part number for the sprue containing the cattlehorns and Islander crest is 8029. Therefore, I want to rename the DAT file for the cattlehorn piece to "8029a.dat", and the name I'll be using for the Islander crest will (...) (24 years ago, 14-Sep-00, to lugnet.cad.dev)
|
| |
| | formula 1 race car [DAT]
|
|
Here my first design with mlcad and my first post in this newsgroup I hope you all like it, comments are always welcome My next project is a 8 stud wide scania truck for minifigs but that takes more time then i thought Eric 0 FILE ferrari.dat 0 (...) (24 years ago, 14-Sep-00, to lugnet.cad.dat.models)
|
| |
| | Again about my programs EMF9X and ELL9X
|
|
I need to know want does everyone think about my programs before I continue my programs. at (URL) e-mail at eduardov@activanet.es (24 years ago, 14-Sep-00, to lugnet.cad)
|
| |
| | Re: www.ldraw.org
|
|
(...) To be sure that you can eventually connect to it try: ping -i 255 www.ldraw.org That is to use the maximum TTL. I tryed it and Got: Reply from 130.226.51.217: bytes=32 time=240ms TTL=227 Which is very near the limit. (...) In Fact the packet (...) (24 years ago, 14-Sep-00, to lugnet.cad, lugnet.general, lugnet.loc.au, lugnet.org.au, lugnet.off-topic.geek)
|
| |
| | Re: Yet another Part name and number wanted ;-)
|
|
(...) I agree more with Fredrik on this. In my case, even though I "file" these pieces with my other "vegetation" pieces, I _call_ the thing "a 1x1 round brick with 3 leaves". When you first look at it, that's what you see, an otherwise regular 1x1 (...) (24 years ago, 14-Sep-00, to lugnet.cad)
|
| |
| | Re: "Needs Work"- Needs Work
|
|
(...) Basically, the idea is that each new partfile would be carefully reviewed by a small number of people (between 1 and 3 reviewers per file, I think). Once the reviewers and the author agreed on the part, it would be released. As soon as I can, (...) (24 years ago, 14-Sep-00, to lugnet.cad.dev)
|
| |
| | Re: Yet another Part name and number wanted ;-)
|
|
(...) I'd rather go with Plant Leaves 3 x 3 Bamboo This will make it easier for people to find the part. And Hakan wrote: (...) I have no idea what the number is. Generally, the procedure is that you use whatever name you want for the file. When you (...) (24 years ago, 14-Sep-00, to lugnet.cad)
|
