|
|
 | | Re: The Unofficial LEGO Advanced Building Techniques Guide
|
| (...) Here the .doc document splitted : Introduction, vocabulary and SNOT : (URL) (click "télécharger document") Offseting : (URL) From Letterings to Disclaimer : (URL) OpenOffice version : (URL) (17 years ago, 23-Feb-07, to lugnet.build.schleim)
| | | | | Re: Smallest cube ever!?
|
| (...) No, the real trick is in getting 1x1 tiles out of the 2x2 brick afterwards! Jason R (17 years ago, 23-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Smallest cube ever!?
|
| (...) Hi, Here is my attemp of a 3x3x3 cube: (3 URLs) The two 1x3 sides are a bit fragile because they are only cliped on less than half the height of a stud. This cube will be then probably disqualified for that, but maybe it will give some ideas (...) (17 years ago, 23-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Smallest cube ever!?
|
| (...) To both reply to this post and the one mentionned by Didier about the sturdyness, I noticed that if you put the 4 1x1 tiles stud out and in the exact middle of the 2x2 tile then the building will be more sturdy than putting the 1x1 tiles in (...) (17 years ago, 23-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Smallest cube ever!?
|
| (...) hmmm. I have a suspicion that most non-integer cubes are impossible because of the way the surfaces can be constructed. Each side of a surface must be constructed out of I + 1/5 J plate units (I and J integer) since we can only make them out (...) (17 years ago, 22-Feb-07, to lugnet.build.schleim, lugnet.off-topic.geek, FTX)
| | | | | Re: Smallest cube ever!?
|
| Of course, the thing that's still missing is the 3x3x3 cube! We've discovered how to make a 2x2x2, a 4x4x4, 5x5x5, and anything larger that's an integer multiple of studs... But no 3x3x3's :( The other thing that I haven't seen tried is making (...) (17 years ago, 22-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Smallest cube ever!?
|
| (...) AH! Well, there you go. I missed that the first time around. Leave it to Bram and Dan though to beat me to it. The've both been at it longer than I. Good work all. (17 years ago, 22-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Smallest cube ever!?
|
| (...) It seems we are condemned to re-discover endlessly building tricks : (URL) (17 years ago, 22-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Smallest cube ever!?
|
| As per this challenge way back 3 years ago ( (URL) ), I present the 2x2x2 cube. No gap this time from the technic half pin. It doesn't fit quite tight but usually will not fall apart when picked up either. This is inspired by (URL) . (2 URLs) (17 years ago, 22-Feb-07, to lugnet.build.schleim, lugnet.announce.moc, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) Mark Stafford had this Asimov-style ship (2 URLs) at LegoWorld that uses cheesers near the front to close the gap between the two wedges. Jason R (17 years ago, 21-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) :-) scheep...? schafe! (or "schapen" in my native language) (...) That is a pretty good idea, does someone know any example of someone using this already? With friendly greetings, M, Moolhuysen. (17 years ago, 21-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) Yes, but the studs were out of aschlignment. And we can talk about scheep if we want to... Anyway, the new 1x1 'cheeser' slopes would be best to pad the gap, if it was the right size. Jason R (17 years ago, 21-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) In lugnet.build.schleim, Ross Crawford answered: (...) ...that can be filled adequately by tiles or plates + tiles attached snotwise. (Oops, I just realised I've put this thread back on-topic, because up until now the discussion was most about (...) (17 years ago, 20-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) Brickish sheep: (URL) and ram: (3 URLs) (Mark Palmer) Jason R (17 years ago, 20-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) -snip- I shall have to build a flock just to try this for myself! Cheers! Richie Dulin (17 years ago, 20-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) Believe it or not, I worked some of this out whilst placing sheep. We use a lot of the sheep based on a 2x3 brick, but they all tend to line up in the same direction. So, next time you're building a flock, try this: Place two 1x1 round plates (...) (17 years ago, 19-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) This is very cool! It seems obvious now you've highlighted it, but I could never have spotted it. (I can't wait to use it in practice!) Thanks for sharing! Cheers Richie Dulin (17 years ago, 18-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) Indeed. Wider bricks/plates do result in a correspondingly larger gap though. ROSCO (17 years ago, 18-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) For the sake of completeness, it's worth to mention this technique not only works for any length, but also for any width of plate/brick. In other words, you're able to slant ? x 2, ? x 4 and so on by mirroring along the diagonal as well, using (...) (17 years ago, 18-Feb-07, to lugnet.build.schleim, FTX)
| | | | | Re: Hinge wall alignment
|
| (...) Note that this technique is used in the nose of the UCS X-wing over a length of 28 studs: [LEGOSet 7191] ROSCO (17 years ago, 18-Feb-07, to lugnet.build.schleim, FTX)
|
|
