 | | Container grabber —Allan J. Smith
|
| | | While experimenting with the red container grabber as used in 4555 I noticed that the holes for the black rubber are the same size as a stud. I have now modified one so that it has grab arms that can lift and load my grey piggyback trailers onto the (...) (24 years ago, 19-Jan-00, to lugnet.books, lugnet.build, lugnet.trains)
|
| | | |
| | | | | Re: Container grabber —Jeremy Spin
|
| | | | | (...) Hey thats a good Idea. Due to lack of room its hard to have a switch track to a ramp. So I'll have to try that comcept. Just have to build a stout crain to support the weight. Thanks J.W.Hummer www.geocities.com/spincity999 (24 years ago, 19-Jan-00, to lugnet.books, lugnet.build, lugnet.trains)
|
| | | | | |
| | | | | | | Re: Container grabber —Jeremy Spin
|
| | | | | | (...) I just built the grabber. I extended it by 6x1 & added a 4x1 plate to the bottom inside. The only problem is that last year (99) I started to build trailer 6x?? so now I'll have to build 4x?? trailers for small trucks & 6x?? for large trucks. (...) (24 years ago, 20-Jan-00, to lugnet.books, lugnet.build, lugnet.trains)
|
| | | | | | |
| | | | | | | | Re: Container grabber —Allan J. Smith
|
| | | | | | The grabber I made is designed to lift my 6 wide piggyback trailers as seen on my webpage. (it will also lift 4 wide trailers). It uses L shaped 2x2 plates in the 4 holes of the red grabber. Attached to the outside of the plates is a 8x1 block. On (...) (24 years ago, 20-Jan-00, to lugnet.build, lugnet.trains)
|
| | | | | | |
| | | | | | | | Re: Container grabber —Jim Rorstrom
|
| | | | | | (...) Please do show us some detailed photos. The overhead crane is in need of a design impovement to make it useful (able to pick up piggyback trailers). Jim --- (24 years ago, 20-Jan-00, to lugnet.build, lugnet.trains)
|
| | | | | | |
| | | | | Re: Container grabber —Richard Dee
|
| | | | On Wed, 19 Jan 2000 04:02:08 GMT, Allan J Smith uttered the following profundities... (...) For those with the tractor wheel links, the inside "tubes" of 1x4 plates fit into the holes on the links.... (24 years ago, 30-Jan-00, to lugnet.books, lugnet.build, lugnet.trains)
|
| | | | |
| | | | | | Re: Container grabber —Larry Pieniazek
|
| | | | (...) But not very well. They have a tendency to pop out again. At least that's been my experience. Anyone have any clues as to how to get them to stay? (24 years ago, 30-Jan-00, to lugnet.books, lugnet.build, lugnet.trains)
|
| | | | |
| | | | | | Re: Container grabber —Christopher Masi
|
| | | | Glue? Chris Just couldn't resist. (...) (24 years ago, 31-Jan-00, to lugnet.books, lugnet.build, lugnet.trains)
|
| | | | |
| | | | | | Re: Container grabber —Larry Pieniazek
|
| | | | (...) Bite your tongue. But glue it to the roof of your mouth first so that it really hurts. Infidel. (24 years ago, 31-Jan-00, to lugnet.books, lugnet.build, lugnet.trains)
|
| | | | |
