 | | Disconnections etc.
|
|
I have a few problems with the Handyboard I just put together: 1. I lose contact with the board from IC very often. Then, when I try to reset the board it will not always reboot. One of the following usually happens: a) I just get the single line of (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | An answer from Polaroid
|
|
A while back I asked if anyone knew about a socket to accomodate the 9-pin plugs that come with the Polaroid sonar modules. I feel pretty dumb now, because I talked with the people at Polaroid, who tell me that it's not really a plug at all; it's (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: How i can beep the handy in Imgecraft C....
|
|
Hi German, I sent this to you before, but I guess you didn't keep it. This one is going to both the robot-board and handyboard lists you can always find it again later by searching the archives for these lists. To beep the beeper using ImageCraft C (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: pneumatics
|
|
(...) Small pneumatics are tough because commercial actuators are (A) expensive and (B)they assume a stationary machine tied to "shop air", i.e. miniature mobile compressors/regulato.../receivers are nonexistant. HOWEVER; you still have 3 good (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Gear Motors
|
|
(...) Check out Herbach and Rademan at www.herbach.com for surplus DC gearhead motors. They often have 6-24 volt, optically encoded motors for $20-$25 each. J.V. -- ***...*** * John Vaughn Phone: 315-781-3906 * * Dept. of Math & Computer Science (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Re: pneumatics
|
|
(...) The components you're looking for sound exactly like ones that came with my Lego Technic kit. The actuator cylinders come in two sizes (the big one's about the size you're looking for), and there's a compressor cylinder and pressure reservoir (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | pneumatics
|
|
does anyone know of a good sourec for pneumatics? Im especially interested in smaller pneumatics, like those about 1-2" long, with a stroke of 1-1.5" Thanks! phil (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | Nowbody can help me???
|
|
I can't believe nowbody of the list users know how works the sound routines in the handyboard??? Please, if any have idea of how i can implement that on OTHER C COMPILER (don't interactive C), please anwser to my question. P.D,: Remember , the (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | robots rising program
|
|
Hi Guys, Get off the computer and tune to the discovery channel to catch this program comming on at 8:00 cst. I believe it is going to last one hour. Bye Terry P Gathright (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
| |
| | ? Mabuchi RS280 motor
|
|
Hello all, I've connected a mabuchi rs280 motor to the handyboard. When activated with the following command, "motor(0,12);" the motor speeds up and then stops, and the board also beeps. the ratings for the motor are as follows voltage range 6-9 (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
|
