| | reset vector
|
|
Hi, I am trying to run a basic assembled .asm file on the handy-board without IC. Since the board doesn't have a reset button, do I use the power on reset (turning board off/on) vector location of $FFFF:$FFFF to indicate the start of my code? -Luke (28 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Polaroid Sonar
|
|
Recently got my OEM kit from Polaroid Corp. In the readme file which i ftped from cherupakha.media.mit...trib/kent, it says "for robust operation solder a 0.01uF cap to C7 of the ranging board." I browsed through the schematic and component layout (...) (28 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: HELP!
|
|
when using DLM, does the downloader make it to the second stage of the download, indicating "synchronized"? also, when attempting to download "config0c.s19," do you give DLM the command line flag indicating to burn EEPROM and not RAM? you must tell (...) (28 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re[2]: expansion board
|
|
Actually I wanted an analogue signal giving some idea of distance. I've done it with a 555 oscillator for illumination, and an opamp demodulator circuit. I was thinking that this might be useful on the expansion board. Richard ___...___ Reply (...) (28 years ago, 18-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: downloading
|
|
(...) Did you run the strip_cr utility on the .S19 file to make the file's lines end correctly? * Michael L. Ross/C33 | Lockheed Martin Eng & Sci Svcs Co. **** * Robotics Department | 2400 Nasa Rd. 1, Houston, TX 77058***** * (281)333-7094; (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | HELP!
|
|
I hope that someone reading this can please help me with a problem that I am finding difficult to solve. I have completed section 4.3 "Micropro and Oscilaator cct" and confirmed that the oscillator is running. However after section 4.4 "Serial line (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | problems downloading own .asm
|
|
Look at the .s19 file, and see if it's downloading anything between 0 and FF. (You should be able to stare at your .s19 file and the pcode for a while and figure out the 4 hex bytes which contain the address for a line). Downloading something to the (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Re: Motors & handyboard
|
|
(...) What is 20? (...) Current meters have an internal resistance. The lower the current range the larger the resistance --- even with digital current meters. Some typical values For example: Digital Analogue Current Range R_meter R_meter 200 uA (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | downloading
|
|
HI, I cannot get any .s19 file except for pcode_hb.s19 to download to the handy-board. This downloads and when I run IC it all works fine. The .s19 file I would like to download is just a normal .asm file assembled with as11.exe. I am just putting (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
|
| | Compiling (interactive) C programs
|
|
Hi all, Some time ago I found a link somewhere on the handyboard page. This link referred to to someone who made a interactive C compiler for Unix environment. I would really like a compiler for the handyboard instead of the the C interpreter.(for (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|