|
In lugnet.robotics, Steve Hassenplug wrote:
> > > At this point, we're not interested in making the standard more complex,
> > > and
> > > increasing the difficulty of setting it up, when it really doesn't add any
> > > functionality to the whole contraption.
> >
> > Well, perhaps some things need more complexity, although I would agree a
> > standard anyone can use is preferable. The big challenge is getting the
> > degree of complexity as best you can for all parties which will be involved.
> >
> > Geoffrey Hyde
>
>
> Is there something that a module builder can not do because the standard is too simple?
>
> Steve
Not to oversimplify, but I mean if the 'standard' for the ball contraption is 32
studs from the front of the hopper to the back edge of the baseplate, and thus I
personally would probably grab a 32 x 32 stud baseplate to build on, thus the
'in' hopper would be in the bottom left hand corner anyway, wouldn't my module,
by its very nature, be able to be placed 'in line' with the other ones, or 90
degrees, placing the hopper in the same location?
I think that making 90 degree turns (only to the right) would be able to be done
on many modules, just the way they are--phenominal ASCII graphix below!
XXXXXXXXXXYYYYYYYYYY
X XY Y
X XY Y
X XY Y
X XY Y
OOO XOOO YOOO
O O XO O YO O
OOOXXXXXXXOOOYYYYYYYOOO
XXXXXXXXXX
X X
X X
X X
X X
OOO XOOOYYYYYYY
O O XO O Y
OOOXXXXXXXOOO Y
Y Y
Y Y
Y Y
Y Y
YYYYYYYYYY
OOO
O O
OOO
X-Module 1
Y-Module 2
O-Input/Output Bin
See, if you leave both 'outer edges' of the bin open, both orientations work
But maybe I'm missing something.
Dave K
|
|
|
In lugnet.robotics, tmassey@obscorp.com wrote:
> news-gateway@lugnet.com wrote on 01/10/2005 10:01:48 AM:
>
> > > Is there something that a module builder can not do because the
> > standard is too simple?
> >
> > Not to oversimplify, but I mean if the 'standard' for the ball
> > contraption is 32
> > studs from the front of the hopper to the back edge of the
> > baseplate, and thus I
> > personally would probably grab a 32 x 32 stud baseplate to build on, thus the
> > 'in' hopper would be in the bottom left hand corner anyway, wouldn'tmy module,
> > by its very nature, be able to be placed 'in line' with the other ones, or 90
> > degrees, placing the hopper in the same location?
>
> That assumes that there is nothing in front of the hopper. There is
> nothing to say that you are limited to a module 32 studs deep. If you
> choose to build it that way, great, but there is nothing that says you
> can't build a 3-foot-deep module (and according to the spec, that *should*
> be longer than deep, so it would have to be at *least* 3 feet long!). In
> that case, it could not turn the corner as you've described.
>
> However, to me, that's even more reason to leave the spec alone. You have
> described a simple way to make a spec-compliant module that makes right
> corners. Therefore, there is no reason to define corner pieces! They're
> already defined! :)
>
> Tim Massey
I completely agree with that assessment. However, the premise is that I'm using
a 32x32 baseplate with the hopper in the bottom left hand corner--using that
premise, the module can be used either in-line, or 90 degrees. If one does not
use the 32x32 baseplate with the hooper in the bottom left-hand corner, then all
bets are off ;)
Dave K
|
|
|
news-gateway@lugnet.com wrote on 01/10/2005 10:01:48 AM:
> > Is there something that a module builder can not do because the
> standard is too simple?
>
> Not to oversimplify, but I mean if the 'standard' for the ball
> contraption is 32
> studs from the front of the hopper to the back edge of the
> baseplate, and thus I
> personally would probably grab a 32 x 32 stud baseplate to build on, thus the
> 'in' hopper would be in the bottom left hand corner anyway, wouldn'tmy module,
> by its very nature, be able to be placed 'in line' with the other ones, or 90
> degrees, placing the hopper in the same location?
That assumes that there is nothing in front of the hopper. There is
nothing to say that you are limited to a module 32 studs deep. If you
choose to build it that way, great, but there is nothing that says you
can't build a 3-foot-deep module (and according to the spec, that *should*
be longer than deep, so it would have to be at *least* 3 feet long!). In
that case, it could not turn the corner as you've described.
However, to me, that's even more reason to leave the spec alone. You have
described a simple way to make a spec-compliant module that makes right
corners. Therefore, there is no reason to define corner pieces! They're
already defined! :)
Tim Massey
|
|
|