| | | | |
| |
| I have a few opinions on the lubrication issue:
1. I would be wary of anything water-soluble/organic as it might grow mold
etc and perhaps start to smell. Leave some out for a week or two and give
it the 'nose' test before using.
2. Even though silicone is clear and inert I would not use that because it
'creeps'. Soon, all your LEGO parts will become coated with a thin layer,
attracting dirt. Also, it's hard to wash off. I managed a bank of silicone
addition pumps in a plastic-molding plant and trying to keep the equipment
clean was a major problem.
3. My choice would be white lithium grease, that you can purchase in small
tubes at an automotive supply store. Service people use it on car hinges
because it does not do serious damage to clothing. Again, I would find a
LEGO block and test it first to be sure that it is compatable with that plastic.
Regards, Jerry
In lugnet.robotics, Tobbe Arnesson writes:
> Hey!
>
> Some lubricant's are especially made for lubricating thin latex night
> wear that I won't mention since this is a family news station... Let's
> just say the latex thingie is used to keep the number of kidos down.
>
> But I bet the clerks will wrinkle their eyebrow if you walk up to a
> desk with not-said lubricant and a large box of LEGOs :)
>
> /Tobbe
>
> On Wed, 4 Apr 2001 12:16:39 GMT, "Troy McLucas" <tmclucas@psu.edu>
> wrote:
> > How about a water-based lubricant instead of petroleum-based? If it's safe for
> > latex...why not ABS? :) Use it sparingly and only as a last resort. Personally,
> > I doubt I would use graphite. Graphite would be a little too messy for me.
| | | | | | | | | | | | | > 3. My choice would be white lithium grease, that you can purchase in
small
(BANGS HEAD)
THAT WAS IT!!!
lithium grease. man oh man why couldn't i think of that. it evens quiets
things very well.
mike "hitting his head" fusion
| | | | | | | | | | | | | | |
| |
| In lugnet.robotics, Jerry Kalpin wrote:
> I have a few opinions on the lubrication issue:
>
> 1. I would be wary of anything water-soluble/organic as it might grow mold
> etc and perhaps start to smell. Leave some out for a week or two and give
> it the 'nose' test before using.
>
> 2. Even though silicone is clear and inert I would not use that because it
> 'creeps'. Soon, all your LEGO parts will become coated with a thin layer,
> attracting dirt. Also, it's hard to wash off. I managed a bank of silicone
> addition pumps in a plastic-molding plant and trying to keep the equipment
> clean was a major problem.
>
> 3. My choice would be white lithium grease, that you can purchase in small
> tubes at an automotive supply store. Service people use it on car hinges
> because it does not do serious damage to clothing. Again, I would find a
> LEGO block and test it first to be sure that it is compatable with that plastic.
>
> Regards, Jerry
For lubing up my Pneumatics, I used Permatex Super lube, A synthetic grease made
by Loctite. Seems to act like any other grease, and have not had any problems
with it.
Chris Pritchard
>
>
> In lugnet.robotics, Tobbe Arnesson writes:
> > Hey!
> >
> > Some lubricant's are especially made for lubricating thin latex night
> > wear that I won't mention since this is a family news station... Let's
> > just say the latex thingie is used to keep the number of kidos down.
> >
> > But I bet the clerks will wrinkle their eyebrow if you walk up to a
> > desk with not-said lubricant and a large box of LEGOs :)
> >
> > /Tobbe
> >
> > On Wed, 4 Apr 2001 12:16:39 GMT, "Troy McLucas" <tmclucas@psu.edu>
> > wrote:
> > > How about a water-based lubricant instead of petroleum-based? If it's safe for
> > > latex...why not ABS? :) Use it sparingly and only as a last resort. Personally,
> > > I doubt I would use graphite. Graphite would be a little too messy for me.
| | | | | | |