|
In lugnet.cad.dev, Kevin L. Clague writes:
> In lugnet.cad, Orion Pobursky writes:
> > I was trying to get a BOM for a model I did and LPub give me a file not
> > found in the Parts.lst eror and quits. The particutlar error was the
> > s/faxle parts used for the flexible axles. Here's my request:
> >
> > If Lpub detects s/faxle1 though s/faxle5, then can it sub a flexble axle
> > part in the BOM and not quit? At the very least I'd like it to not quit on
> > error.
>
> Hi Orion,
>
> I recommend that you put a PLIST BEGIN IGN before the s/faxle1 and PLIST END
> after each s/faxle1. LPub will ignore these parts and not give you an error.
>
> Even better, create a stright version of the xale in a seperate dat and use
> this:
>
> PLIST BEGIN SUB <mystraightaxle.dat>
> 0 // your multiple parts that make up the axle are in here
> PLIST END
>
> LPub will ignore all the synthesized stuff, and instead render
> mystraightaxle.dat and use it in the part list iamge and BOMs.
>
> I know you do not use lsynth because you have your own mechanism for
> flexible axles, but......
>
> LPub recognizes lsynth specifications and does some special handling. In
> the case of flexible axles, it calculates the length of the axle based on
> the synthesized parts, then creates a straight version of the part and
> renders it for the part list image.
>
> Kevin
>
> >
> > -Orion
OK, I used the PLIST BEGIN command and I'm still getting the s/faxle1.dat
not found in the PARTS.LST file error. I think (but haven't tried) that
this problem will exist for any model that uses file from the /S directory.
-Orion
|
|
|
Hi Orion,
Go to Building Instructions->Controls and uncheck "Check DAT(s) against
Part List".
Kevin
In lugnet.cad.dev, Orion Pobursky writes:
> In lugnet.cad.dev, Kevin L. Clague writes:
> > In lugnet.cad, Orion Pobursky writes:
> > > I was trying to get a BOM for a model I did and LPub give me a file not
> > > found in the Parts.lst eror and quits. The particutlar error was the
> > > s/faxle parts used for the flexible axles. Here's my request:
> > >
> > > If Lpub detects s/faxle1 though s/faxle5, then can it sub a flexble axle
> > > part in the BOM and not quit? At the very least I'd like it to not quit on
> > > error.
> >
> > Hi Orion,
> >
> > I recommend that you put a PLIST BEGIN IGN before the s/faxle1 and PLIST END
> > after each s/faxle1. LPub will ignore these parts and not give you an error.
> >
> > Even better, create a stright version of the xale in a seperate dat and use
> > this:
> >
> > PLIST BEGIN SUB <mystraightaxle.dat>
> > 0 // your multiple parts that make up the axle are in here
> > PLIST END
> >
> > LPub will ignore all the synthesized stuff, and instead render
> > mystraightaxle.dat and use it in the part list iamge and BOMs.
> >
> > I know you do not use lsynth because you have your own mechanism for
> > flexible axles, but......
> >
> > LPub recognizes lsynth specifications and does some special handling. In
> > the case of flexible axles, it calculates the length of the axle based on
> > the synthesized parts, then creates a straight version of the part and
> > renders it for the part list image.
> >
> > Kevin
> >
> > >
> > > -Orion
>
> OK, I used the PLIST BEGIN command and I'm still getting the s/faxle1.dat
> not found in the PARTS.LST file error. I think (but haven't tried) that
> this problem will exist for any model that uses file from the /S directory.
>
> -Orion
|
|
|