 | | Re: Hopper car model
|
|
(...) You can also post it to the RailBricks gallery. Russell (16 years ago, 23-Dec-08, to lugnet.trains, FTX)
|
| |
| | Re: Hopper car model
|
|
(...) In addition to the places you mentions, the (URL) site allows you to set up a gallery. There's a lot of cross-over between forums, but that site is also beginning to pick up some users who are new to the hobby. -Elroy (who'll probably build a (...) (16 years ago, 23-Dec-08, to lugnet.trains, FTX)
|
| |
| | Re: Reshaping 4.5v track
|
|
(...) I’ve had some success using a heat gun although you have to monitor the temperature extremely closely. You could also try making small cuts on the inside of the curve rails, but i've never tried this method myself. ondrew (16 years ago, 23-Dec-08, to lugnet.trains)
|
| |
| | Hopper car model
|
|
A few months back I designed a (URL) train car: (URL) And recently I built LDraw instructions for it and published them online. What's the best way to share them? I put the CAD file (URL) on my blog> and on Flickr (as a comment under the (URL) 3D (...) (16 years ago, 23-Dec-08, to lugnet.announce.moc, lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Beating up, kicking, and verbally abusing an old dead rotted horse...
|
|
(...) (URL) (16 years ago, 23-Dec-08, to lugnet.trains, lugnet.general)
|
| |
| | Reshaping 4.5v track
|
|
I am wanting to use my old 4.5v tracks for a narrow gauge train that will be 4 studs wide. Obviously the straight track is fine, but it is the curve track that is giving me some bother. Can anyone suggest a solution? (16 years ago, 23-Dec-08, to lugnet.trains)
|
| |
| | What I want for Christmas
|
|
If LEGO granted Christmas wishes, I would have to ask for: 1) 5.5 length technic axle - so my train wheels don't fall off anymore 2) modular train railing system - so I don't have to cut any more hose and the awkward use of minifig hands 3) train (...) (16 years ago, 22-Dec-08, to lugnet.general, lugnet.trains, lugnet.lego.direct, FTX)
|
| |
| | Re: Western Train with instructions
|
|
--snip-- (...) Oh dear. I started to build one and found a fairly big mistake... The front set of big wheels must be replaced by a set of BBB unflanged wheels. The yellow domes must be attached on a top corner, not in the middle. I'll update the (...) (16 years ago, 20-Dec-08, to lugnet.trains, FTX)
|
| |
| | Santa and his Reindeer
|
|
A few years ago I put LEGO train tracks around my son's roof towards the ceiling. This year, I made a team of reindeer and a sleigh to run around the tracks. The Santa is an old LEGO set, but the reindeer and sleigh are MOC. I'm not completely (...) (16 years ago, 19-Dec-08, to lugnet.trains, lugnet.fun.holiday, FTX)
|
| |
| | Seasonal Community Spirit
|
|
Maybe the time of year has something to do with it, but I must confess to have been moved by the generosity of a few talented builders lately. Seperately, we’ve seen (URL) Eric Sophie>, (URL) Tim Gould> and (URL) Mark Neumann> sharing not only their (...) (16 years ago, 16-Dec-08, to lugnet.general, lugnet.inst, lugnet.people, lugnet.trains, lugnet.build.mecha, lugnet.cad, lugnet.western, FTX) !!
|
| |
| | Re: Western Train with instructions
|
|
(...) The final two stages are now up (URL) Loco and tender - (URL) (as (URL)) Passenger - (URL) ((URL)) Lumber- (URL) ((URL)) Boxcar - (URL) ((URL)) Caboose - (URL) ((URL)) Please note I've also resubmitted instructions for the Loco (and boxcar and (...) (16 years ago, 16-Dec-08, to lugnet.trains, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) Ahhh I found them. The original loco and the last two. I must have accidentally switched LPub across to a different setting before doing (and redoing in the case of the loco) the instructions. Newer versions will be uploaded. Tim (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) So do I but going back to the original issue which instructions are using the black edgelines? Tim (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) I agree fully with Philo's thoughts about the "Always black" edgelines. cu mikeheide (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) I always considered that "Always black" was unusable since dark colors were illegible. So for me the answer is yes. I would be tempted to push the threshold further: even if there is enough contrast on screen, it could be insufficient in (...) (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) I agree that dark gray would have worked better for these edge lines. I can easily change "always back" in LDView to be "usually black". I played around with the settings a bit, and with r * 30 + g * 59 + b * 11 <= 3600 as my threshold for (...) (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
(...) See the difference between your instructions and those I created from the MPD: (URL) guess is that your LDView lpub setup has edge lines set to "always black" Philo (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad)
|
| |
| | Re: Western Train with instructions
|
|
(...) Thanks! Strange. The edgelines show up very clearly on my system. I'm curious how other people find them? They're set to something similar to dark grey. Tim (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Re: Western Train with instructions
|
|
Hi Tim, Wonderful models and instructions! (no I'm not turning train ;o)... But I find the edgelines of black parts much too dark, making these parts illegible. What setup did you use? Philo (16 years ago, 16-Dec-08, to lugnet.trains, lugnet.cad, FTX)
|
| |
| | Stage III Re: Western Train with instructions
|
|
(...) --snip-- Stage III is up now. (2 URLs) ((URL)). Tim (16 years ago, 16-Dec-08, to lugnet.trains, FTX)
|
