 | | Re: My Train Yard...
|
|
(...) That my friend...is a lot of rolling stock. Very cool and thanks for sharing. -Dave ToT-LUG (16 years ago, 21-Sep-08, to lugnet.trains, FTX)
|
| |
| | My Train Yard...
|
|
(URL) (16 years ago, 21-Sep-08, to lugnet.trains, FTX)
|
| |
| | Re: Is there a reference site on motorized switchs
|
|
(...) Try these. There is some good information on all of them. (URL) FreeLUG Article on Motorized Points> (URL) Automated 9V Switch> (URL) Mark Riley's Solution> Good luck and happy building! -Dave ToT-LUG (16 years ago, 18-Sep-08, to lugnet.trains, FTX)
|
| |
| | Is there a reference site on motorized switchs
|
|
I thought I had found one once, but then seem to have lost track of it, HELP!! (16 years ago, 18-Sep-08, to lugnet.trains)
|
| |
| | Re: Automated Level Crossing using NXT
|
|
quite neat. I hope you can figure out the correct switching delays for the micromotor. Do you think this technique could be used to make a monorail level crossing ? Steve (16 years ago, 11-Sep-08, to lugnet.trains, FTX)
|
| |
| | ATSF Piggy-Back Service (Flatbed w/Truck Trailer) MOC
|
|
Here's my latest train MOC. This is an ATSF Piggy-Back Service train... (2 URLs) Here's the model it was based on: (URL) Mark (16 years ago, 9-Sep-08, to lugnet.trains, FTX)
|
| |
| | New Red Chemical Car
|
|
I managed to snag some rare dark red brick from a grab bag at the local Lego store. The dark red pieces are from set 7665 (Republic Cruiser). I then combined them with some extra train parts and you get what you see below. The end result was this (...) (16 years ago, 9-Sep-08, to lugnet.trains, FTX)
|
| |
| | Re: Automated Level Crossing using NXT
|
|
That is an excellent system for controlling train crossings. I love that it is all above the baseplates and only uses one motor for both crossings. I have two suggestions for the motor timing on raising and lowering of the gates: 1) Use a Technic (...) (16 years ago, 6-Sep-08, to lugnet.trains)
|
| |
| | Re: Trains, Car and Level Crossing Automatic Control System
|
|
(URL) (16 years ago, 6-Sep-08, to lugnet.trains, FTX)
|
| |
| | Trains, Car and Level Crossing Automatic Control System
|
|
This system is used 4 RCXs to control 2 trains, 1 car and 1 level crossing. RCX1 is used to control 3 switch points and response 3 light sensors. RCX2 is used to control 3 segments track and response 2 light sensors. RCX3 is used to control level (...) (16 years ago, 6-Sep-08, to lugnet.announce.moc, lugnet.trains, lugnet.robotics.rcx.legos) !
|
| |
| | Re: Automated Level Crossing using NXT
|
|
(...) break at some point, but you seem to have a pretty good system there. (...) Actually, I think you could do this at least partially with a single sensor. If the train is running at a fixed speed, you can have the program figure that speed out (...) (16 years ago, 5-Sep-08, to lugnet.trains, lugnet.robotics.nxt)
|
| |
| | Automated Level Crossing using NXT
|
|
Hey, Here's my go at an automated level crossing using NXT. All pictures in this (URL) folder>. Two movies on YouTube: (URL) Movie 1> (Entire setup) (URL) Movie 2> (Zoom on level crossing) (URL) Here's how it works: The train passes the (URL) (...) (16 years ago, 4-Sep-08, to lugnet.announce.moc, lugnet.trains, FTX)
|
| |
| | New part in crane set
|
|
I was mulling these new parts over while walking to work today: (URL) I was muttering to myself about them being yellow but then I thought they might be good for a spine car or the inside bottom of a container car? (I don't know the exact (...) (16 years ago, 27-Aug-08, to lugnet.trains, lugnet.town)
|
| |
| | Re: My NEW Rio Grande Grain Hopper. Design #2.
|
|
(...) Thanks, Matt. The real tricky part about it is in connecting the 2x3 slope on it's side. Because of the way it must be done, I originally ended up with a slot/gap between the top of the 2x3 slope and the brick above it. The slot/gap was about (...) (16 years ago, 26-Aug-08, to lugnet.trains, FTX)
|
| |
| | Train Display At BrickFair
|
|
(URL) Hey All, If you have registered a Train/Town MOC for BrickFair, or are still planning to register a Train/Town MOC for BrickFair - and you are bringing it on Thursday or early on Friday, it WILL go in the display. I’m going to try to have just (...) (16 years ago, 26-Aug-08, to lugnet.trains, FTX)
|
| |
| | Re: My NEW Rio Grande Grain Hopper. Design #2.
|
|
(...) Great work, Mark. I like how you used the 2x3 slopes in the middle. I may have to steal that in the future. (16 years ago, 26-Aug-08, to lugnet.trains, FTX)
|
| |
| | Re: My NEW Rio Grande Grain Hopper. Design #2.
|
|
(...) Nicely done! Chris (16 years ago, 24-Aug-08, to lugnet.trains)
|
| |
| | Wireless Power for LEGO Trains?
|
|
I know this is a long way off (think 2050) but, on Thursday, Intel revealed prototypes of a new wireless power supply. If this ever comes to market, think of the possibilities! Battery powered LEGO Trains that never need to be charged! NXT bricks (...) (16 years ago, 22-Aug-08, to lugnet.off-topic.geek, lugnet.trains, FTX)
|
| |
| | Re: C&O BL2
|
|
(...) Thanks Cale, I was just lucky that TLG made the dark blue half arch for the nose. (...) That was a cool walk through, I've been through f-units before but never a BL2. Interesting to see just how they worked out the spacing, etc. With the (...) (16 years ago, 20-Aug-08, to lugnet.trains, FTX)
|
| |
| | My NEW Rio Grande Grain Hopper. Design #2.
|
|
Okay, I really like this design the best! It took a good day to hammer out the design, but I think I was more impressed with this finished MOC then with any other MOC I've done. It had some rough spots that had me REALY scratching my head, but in (...) (16 years ago, 19-Aug-08, to lugnet.trains, FTX)
|
