 | | ATSF Piggy-Back Service (Flatbed w/Truck Trailer) MOC
|
|
Here's my latest train MOC. This is an ATSF Piggy-Back Service train... (2 URLs) Here's the model it was based on: (URL) Mark (16 years ago, 9-Sep-08, to lugnet.trains, FTX)
|
| |
| | New Red Chemical Car
|
|
I managed to snag some rare dark red brick from a grab bag at the local Lego store. The dark red pieces are from set 7665 (Republic Cruiser). I then combined them with some extra train parts and you get what you see below. The end result was this (...) (16 years ago, 9-Sep-08, to lugnet.trains, FTX)
|
| |
| | Re: Automated Level Crossing using NXT
|
|
That is an excellent system for controlling train crossings. I love that it is all above the baseplates and only uses one motor for both crossings. I have two suggestions for the motor timing on raising and lowering of the gates: 1) Use a Technic (...) (16 years ago, 6-Sep-08, to lugnet.trains)
|
| |
| | Re: Trains, Car and Level Crossing Automatic Control System
|
|
(URL) (16 years ago, 6-Sep-08, to lugnet.trains, FTX)
|
| |
| | Trains, Car and Level Crossing Automatic Control System
|
|
This system is used 4 RCXs to control 2 trains, 1 car and 1 level crossing. RCX1 is used to control 3 switch points and response 3 light sensors. RCX2 is used to control 3 segments track and response 2 light sensors. RCX3 is used to control level (...) (16 years ago, 6-Sep-08, to lugnet.announce.moc, lugnet.trains, lugnet.robotics.rcx.legos) !
|
| |
| | Re: Automated Level Crossing using NXT
|
|
(...) break at some point, but you seem to have a pretty good system there. (...) Actually, I think you could do this at least partially with a single sensor. If the train is running at a fixed speed, you can have the program figure that speed out (...) (16 years ago, 5-Sep-08, to lugnet.trains, lugnet.robotics.nxt)
|
| |
| | Automated Level Crossing using NXT
|
|
Hey, Here's my go at an automated level crossing using NXT. All pictures in this (URL) folder>. Two movies on YouTube: (URL) Movie 1> (Entire setup) (URL) Movie 2> (Zoom on level crossing) (URL) Here's how it works: The train passes the (URL) (...) (16 years ago, 4-Sep-08, to lugnet.announce.moc, lugnet.trains, FTX)
|
| |
| | New part in crane set
|
|
I was mulling these new parts over while walking to work today: (URL) I was muttering to myself about them being yellow but then I thought they might be good for a spine car or the inside bottom of a container car? (I don't know the exact (...) (16 years ago, 27-Aug-08, to lugnet.trains, lugnet.town)
|
| |
| | Re: My NEW Rio Grande Grain Hopper. Design #2.
|
|
(...) Thanks, Matt. The real tricky part about it is in connecting the 2x3 slope on it's side. Because of the way it must be done, I originally ended up with a slot/gap between the top of the 2x3 slope and the brick above it. The slot/gap was about (...) (16 years ago, 26-Aug-08, to lugnet.trains, FTX)
|
| |
| | Train Display At BrickFair
|
|
(URL) Hey All, If you have registered a Train/Town MOC for BrickFair, or are still planning to register a Train/Town MOC for BrickFair - and you are bringing it on Thursday or early on Friday, it WILL go in the display. I’m going to try to have just (...) (16 years ago, 26-Aug-08, to lugnet.trains, FTX)
|
